?
Solved

Cisco 803 connection problem with laptop........

Posted on 2003-03-06
7
Medium Priority
?
169 Views
Last Modified: 2010-04-17
have Cisco 803 router and GateWay laptop.......I connected the router with laptop through console able with serial port.....Help of hyperterm I can communicate with router. But through Cisco fast setup.....getting error like. not able to communicate with router check your console cable.....(same cable only using hyperterm)
Please help
Thanks
0
Comment
Question by:ponsuresh
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 4
  • 2
7 Comments
 
LVL 79

Expert Comment

by:lrmoore
ID: 8080187
I believe that fast setup will require an ethernet cable also. Use a crossover cable to connect your laptop's LAN card directly to the router's Ethernet port, and use your Hyperterm session to run the setup.
0
 

Author Comment

by:ponsuresh
ID: 8086063
Irmoore,


       I can able to connect with desktop pc without lan cable.
0
 
LVL 79

Expert Comment

by:lrmoore
ID: 8086141
OK, what's different between the desktop and the laptop? Is the router setup in a different location? Ethernet port plugged in/not plugged in to a hub/switch. If one works, the other one should also.
0
Technology Partners: We Want Your Opinion!

We value your feedback.

Take our survey and automatically be enter to win anyone of the following:
Yeti Cooler, Amazon eGift Card, and Movie eGift Card!

 

Author Comment

by:ponsuresh
ID: 8086793
yes, it should connect.....may be laptop comport setting has to chnaged...
0
 
LVL 79

Accepted Solution

by:
lrmoore earned 200 total points
ID: 8087793
Hyperterm should be set to 9600, 8,N,1, no flow control
0
 
LVL 79

Expert Comment

by:lrmoore
ID: 8637111
ponsuresh,
No comment has been added lately (88 days), so it's time to clean up this TA.
I will leave a recommendation in the Cleanup topic area for this question:

RECOMMENDATION: Award points to lrmoore

Please leave any comments here within 7 days.

PLEASE DO NOT ACCEPT THIS COMMENT AS AN ANSWER!

Thanks,

lrmoore
EE Cleanup Volunteer
---------------------
If you feel that your question was not properly addressed, or that none of the comments received were appropriate answers, please post a request in Community support (with a link to this page) to refund your points. http://www.experts-exchange.com/Community_Support/
0

Featured Post

ATEN's HDBaseT Presentation at InfoComm 2017

Hear ATEN Product Manager YT Liang review HDBaseT technology, highlighting ATEN’s latest solutions as they relate to real-world applications during her presentation at the HDBaseT booth at InfoComm 2017.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

It happens many times that access list (ACL) have to be applied to outgoing router interface in order to limit some traffic.This article is about how to test ACL from the router which is not very intuitive for everyone. Below scenario shows simple s…
How to set-up an On Demand, IPSec, Site to SIte, VPN from a Draytek Vigor Router to a Cyberoam UTM Appliance. A concise guide to the settings required on both devices
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses

764 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question