Solved

Cisco 2600 CPU Memory - Mrtg

Posted on 2003-11-04
5
3,964 Views
Last Modified: 2007-12-19
Hi,
I want to use MRTG to graph the cpu usage and memory usage on a cisco 2600 router (IOS ver 12.1), but i cannot find an MIB (OID) to check. Does the current ios support it, if so how, if not, then does the newest ios (12.208)  support it.

Cisco.com is not very helpful at that

Please help
0
Comment
Question by:kolbep
  • 3
  • 2
5 Comments
 
LVL 3

Expert Comment

by:sheahmed
ID: 9684461


OID             cpu1min         1.3.6.1.4.1.9.2.1.57.0
OID             cpu5min         1.3.6.1.4.1.9.2.1.58.0
OID             mem5minUsed     1.3.6.1.4.1.9.9.48.1.1.1.5.1
OID             mem5minFree     1.3.6.1.4.1.9.9.48.1.1.1.6.1

Try in this way
Target[cpu]:.1.3.6.1.4.1.9.2.1.58.0&.1.3.6.1.4.1.9.2.1.58.0:community@1.1.1.1


Regards,
Sheeraz Ahmed
0
 

Author Comment

by:kolbep
ID: 9684633
Thanks Sheeraz,

By the way, do you know any OID for traffic shaping, rate limit, or access lists?
Our upstream provider sets international incoming traffic to dscp af21, and I want to be able to graph only traffic matching that?


Peter
0
 
LVL 3

Expert Comment

by:sheahmed
ID: 9684696
hmm ... u can ...
try ip accounting ... if possible ...

or ... a script in perl will be required ... to plot ur required things ...
0
 
LVL 3

Accepted Solution

by:
sheahmed earned 125 total points
ID: 9684704
i dont find any OID's for the things u mentioned later ... if u find any then let me know as well please ...

can u close this question? discussion may continue ...
0
 

Author Comment

by:kolbep
ID: 9685563
I am trying to export via netflow.
Hopefully that will let me filter by dscp bit

peter
0

Featured Post

Find Ransomware Secrets With All-Source Analysis

Ransomware has become a major concern for organizations; its prevalence has grown due to past successes achieved by threat actors. While each ransomware variant is different, we’ve seen some common tactics and trends used among the authors of the malware.

Join & Write a Comment

Suggested Solutions

While it is possible to put two routes in place with the secondary having a higher metric, this may not always work. In the event of a failure that does not bring down the physical interface on the router the primary route is not removed. There is a…
Hello , This is a short article on how would you go about enabling traceoptions on a Juniper router . Traceoptions are similar to Cisco debug commands but these traceoptions are implemented in Juniper networks router . The following demonstr…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

708 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

14 Experts available now in Live!

Get 1:1 Help Now