Go Premium for a chance to win a PS4. Enter to Win


Error Message: STOP 0x00000001e  ( 0xC0000005 ), 0xED2A146F  KMODE_EXCEPTION_NOT_HANDLED

Posted on 2003-11-24
Medium Priority
Last Modified: 2010-05-18
I looked this BSOD up on the Microsoft site and it asid that I have the Backdoor.NTHack virus.  I also looked on Symantec for information on this virus.  I went into the registry and did not find anything about NewGina, etc.
I ran Dell Diagnostics and all is well.  I opened the case and looked around and blew some canned air to dislodge any dust or dirt.
This BSOD does not appear at start-up, but only after the pc is on for about 45 - 60 mins.  When it comes back, I can reboot and the same thing will happen.
I am at a loss for what to do now.  Having to format the HDD and start over seems extreme, there must be something else.
Question by:rd280z
LVL 44

Accepted Solution

CrazyOne earned 1000 total points
ID: 9811622
This is what MS says about it


This Stop message, also known as Stop 0x1E, indicates that a kernel-mode process tried to execute an illegal or unknown processor instruction. This error handler is a default error handler that catches errors not associated with other specific error handlers.

Interpreting the Message

The four parameters listed in the message are defined in order of appearance as follows:

Exception code that was not handled
Address at which the exception occurred
Parameter 0 of the exception
Parameter 1 of the exception
The first parameter is a Windows 2000 error code, which is defined by the type of error encountered in the file Ntstatus.h of the Windows 2000 Device Driver Kit (DDK). For information about the DDK, see "Additional Resources" at the end of this chapter. The second parameter identifies the address of the module in which the error occurred. Frequently, the address points to an individual driver or piece of faulty hardware, which is generally listed on the third line of the Stop message. Always make a note of this address, as well as the link date of the driver or image that contains it. The last two parameters vary, depending upon the exception that has occurred. You can typically find a description of the parameters that are included with the name of error code in Ntstatus.h. If the error code has no parameters, the last two parameters are listed as 0x00000000.

Resolving the Problem

Hardware incompatibility. First, make sure that any new hardware installed is listed on the Windows 2000 Hardware Compatibility List (HCL).

Buggy device driver or system service. In addition, a buggy device driver or system service might be responsible for this error. Hardware issues, such as memory conflicts and IRQ conflicts, can also generate this error.

If a driver is listed by name within the Stop message, disable or remove that driver. Disable or remove any drivers or services that were recently added. If the error occurs during the startup sequence and the system partition is formatted with NTFS file system, you might be able to use safe mode to rename or delete the faulty driver. If the driver is used as part of the system startup process in safe mode, you need to start the computer by using the Recovery Console to access the file.

If the problem is associated with Win32k.sys, the source of the error might be a third-party remote control program. If such software is installed, the service can be removed by starting the system using the Recovery Console and deleting the offending system service file.

Check the System Log in Event Viewer for additional error messages that might help pinpoint the device or driver that is causing Stop 0x1E. Disabling memory caching of the BIOS might also resolve the error. You should also run hardware diagnostics, especially the memory scanner, supplied by the system manufacturer. For details on these procedures, see the owner's manual for your computer.

One type of this kind of error displays exception code 0x80000003. This error indicates a hard-coded breakpoint or assertion was hit, but the system was started with the /NODEBUG switch. This problem should rarely occur. If it occurs repeatedly, make sure a kernel debugger is connected and the system is started with the /DEBUG switch.

The error that generates this message can occur after the first restart during Windows 2000 Setup, or after setup is finished. A possible cause of the error is lack of disk space for installation and system BIOS incompatibilities. For problems during Windows 2000 installation that are associated with a lack of disk space, reduce the number of files on the target hard disk. Check for and delete any unneeded temporary files, Internet cache files, application backup files, and CHK files containing saved file fragments from disk scans. You can also use another hard disk with more free space for the installation. BIOS problems can be resolved by upgrading the system BIOS version.

For more troubleshooting information about the 0x1E Stop message, refer to the Microsoft Support Web site, using the keywords winnt and 0x0000001E.

Featured Post

Free Tool: Subnet Calculator

The subnet calculator helps you design networks by taking an IP address and network mask and returning information such as network, broadcast address, and host range.

One of a set of tools we're offering as a way of saying thank you for being a part of the community.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

NTFS file system has been developed by Microsoft that is widely used by Windows NT operating system and its advanced versions. It is the mostly used over FAT file system as it provides superior features like reliability, security, storage, efficienc…
Microsoft Access has a limit of 255 columns in a single table; SQL Server allows tables with over 255 columns, but reading that data is not necessarily simple.  The final solution for this task involved creating a custom text parser and then reading…
Are you ready to place your question in front of subject-matter experts for more timely responses? With the release of Priority Question, Premium Members, Team Accounts and Qualified Experts can now identify the emergent level of their issue, signal…
Despite its rising prevalence in the business world, "the cloud" is still misunderstood. Some companies still believe common misconceptions about lack of security in cloud solutions and many misuses of cloud storage options still occur every day. …
Suggested Courses
Course of the Month11 days, 22 hours left to enroll

916 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question