Solved

Configuring Cisco 1760 Routers with a T1

Posted on 2003-12-01
3
610 Views
Last Modified: 2006-11-17
I need to configure two Cisco 1760 Routers with T1 cards and WIC's installed to use on a chanelized T1... chanels 1 through 12 and 24 to be used for voice applications. (I am a novice with Cisco but the Configuration Maker has been a help)
0
Comment
Question by:DarylnCA
  • 2
3 Comments
 

Author Comment

by:DarylnCA
ID: 9855294
I need to configure a SMC 24 port Switch and two Cisco 1760 Routers with T1 cards and WIC's installed to use on a chanelized T1... chanels 1 through 12 and 24 to be used for voice applications. (I am a novice with Cisco but the Configuration Maker has been a help)
0
 
LVL 3

Accepted Solution

by:
sheahmed earned 350 total points
ID: 9855967
DarylnCA ...

no need to worry about configuration, etc ... here you can find a lot of cisco experts and cisco lovers...

configuring channelized T1 isnt a big deal ... just go ahead with the link below ...

http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/dial_c/dcchant.htm#wp4549


Regards,
Sheeraz Ahmed
0
 

Author Comment

by:DarylnCA
ID: 9868703
I guess I needed to clarify the question some...

I need to configure a SMC 24 port Switch and two Cisco 1760 Routers with WIC-1CSU-T1 cards channels 1 through 12 and 24 to be passed through from Router to Router across the T1. I am using the system to pass those channels to a digital phone system and the remaining bandwidth is passing Data between the locations LAN/WAN(I am a novice with Cisco but the Configuration Maker has been a help)
I called Cisco and am waiting a resolution... They get screwed up when I mention phones.
I can currently use the T1 without the Routers to pass the Phone signal from PBx to PBx no problem.

It appears there needs to be an additional WIC card on each router in order to pass the channels across that is being sent to the PBx.
0

Featured Post

How your wiki can always stay up-to-date

Quip doubles as a “living” wiki and a project management tool that evolves with your organization. As you finish projects in Quip, the work remains, easily accessible to all team members, new and old.
- Increase transparency
- Onboard new hires faster
- Access from mobile/offline

Join & Write a Comment

In this tutorial I will show you with short command examples how to obtain a packet footprint of all traffic flowing thru your Juniper device running ScreenOS. I do not know the exact firmware requirement, but I think the fprofile command is availab…
I have seen some questions on problems with SSH/telnet access to Cisco routers that may occur despite the fact that from a PC connected to your LAN, Internet connectivity is in place and users can access Internet sites without any issues.  There are…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

707 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

18 Experts available now in Live!

Get 1:1 Help Now