Solved

Create Name to IP Address

Posted on 2003-12-03
5
327 Views
Last Modified: 2010-03-19
I have 2000 server and I've already created in the Internet world a domain name (domain.net) that routes to my public ip address (206.xxx.xxx.xxx) that then routes to my private ip address (10.xxx.xxx.xxx).  Internally I would like to type in this same domain name (domain.net) and it route directly to (10.xxx.xxx.xxx) so my users can see exactly what the Internet world is looking at.  If they were to type in 10.xxx.xxx.xxx, they'd go exactly where they need to go.  My network was created with domain.local, so this is the only forward lookup zone that I have created in my DNS.  Seems like this should be very easy to create.

Help
0
Comment
Question by:MortgageGuy
  • 3
  • 2
5 Comments
 
LVL 1

Expert Comment

by:Peter1111
ID: 9871850
Hello
You can remove domain.local and create domain.net forward lookup zone instead(Active directory integrated if you have Active Directory ).Also create DHCP with Dinamic updates enabled for your internal clients( subnet 10.x.x.x).After all internally if you type domain.net or 10.x.x.x it'll take you to the same web site.
If you want to keep domain.local zone and you've already done some job there, create  forward lookup zone named domain.net. Then rigth click it and click Alias(CNAME) and follow it. Under "Alias Names" type for instance "www", under "Fully qualified domain name " type name of the server or computer you 'd like to redirect to(w2k.domain.local for exemple) or if you're not sure click browse and find rigth one and click ok. Now internally if you type www.domain.net it will take to the w2k.domain.local web site.So this way on the intranet you can have www.whatever.com
Good Luck
0
 

Author Comment

by:MortgageGuy
ID: 9874830
Almost there.  I would like to change everything from domain.local to domain.net.  I have Active Directory Integrated and DHCP is created with dynamic updates enabled.  I'll look into it a little a further and see what else may need to be involved.  For now, I'd like to just create an additional forward lookup zone called domain.net.  I did as you suggested, but it still won't open a web page.  I can't just type in site.domain.local internally and it go directly to the site in a web browser.  If I type in http://site/ it will.  What am I missing?
0
 
LVL 1

Accepted Solution

by:
Peter1111 earned 250 total points
ID: 9875724
Ok let's do it step by step.under Dns console tree right click on Forward lookup Zones,click NEW Zone,click Next,select Primary Zone(does't have to be an Active Directory integrated)>Next>under zone name type domain.net>next>"Create a new file with this file name" has to be domain.net.dns>next>check Allow both nonsecure and secure dynamic updates button>next>finish. Now you have a new zone named doamin.net. Rigth click it, cilck New Alais (CNAME), under  Alais Name(uses parent doamin if left blank) type "site",under FQDN(fully qualified domain name)for target host type computer FQDN name which hosts web site(for exemple it has to be in your case pcname.domain.local, because you  have Active Directory integrated primary zone---doamin.local) Click ok. Now if you highlight domain.net zone you'll have to have all these:
           Name                                            Type                                       Data
 (same as a parent folder)        Start of Authority(SOA)     (1) pcname.domain.local, hostmaster.domain.local
 (same as parent folder)            Name Server(NS)                         pcname.domain.local
          site                                         Alias(CNAME)                      pcname.domain.local
Type in the address bar site.domain.net...If you still have the same problem ,then I suggest type site.domain.net under Alias name where you typed site as an alias before....I doubt it  but you never know...
0
 

Author Comment

by:MortgageGuy
ID: 9905688
Works just like you said.  Thanks
0
 
LVL 1

Expert Comment

by:Peter1111
ID: 9908270
I'm glad you made it.
Good luck
0

Featured Post

Manage your data center from practically anywhere

The KN8164V features HD resolution of 1920 x 1200, FIPS 140-2 with level 1 security standards and virtual media transmissions at twice the speed. Built for reliability, the KN series provides local console and remote over IP access, ensuring 24/7 availability to all servers.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

We recently endured a series of broadcast storms that caused our ISP to shut us down for brief periods of time. After going through a multitude of tests, we determined that the issue was related to Intel NIC drivers on some new HP desktop computers …
This article offers some helpful and general tips for safe browsing and online shopping. It offers simple and manageable procedures that help to ensure the safety of one's personal information and the security of any devices.
In an interesting question (https://www.experts-exchange.com/questions/29008360/) here at Experts Exchange, a member asked how to split a single image into multiple images. The primary usage for this is to place many photographs on a flatbed scanner…

730 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question