Solved

wrong system software for my router (cisco 3620)

Posted on 2004-04-22
3
671 Views
Last Modified: 2007-12-19
Hello every one!!

I have cisco 3620 router. I made a mistake when I upgrade the software. my previous image was c3620-i-mz.120-4.T. I erased it and copy the image c3640-i-mz.122-19a.bin from TFTP server. After I finished, I reloaded it. But when it boots, it says "wrong system software for this hardware"  continously so that it can't start. How can I correct my problem please? or how can I copy the previouse image to my router from TFTP server? Actually I have taken back up the flash image before I upgraded.
0
Comment
Question by:melkamu93
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
3 Comments
 
LVL 43

Accepted Solution

by:
JFrederick29 earned 500 total points
ID: 10887866
Within the first 60 seconds of the router booting, press CTRL-BREAK in Hyperterminal to enter rommon mode.

Once in rommon, you need to set the following variables:

IP_ADDRESS—IP address for the router you are using.
IP_SUBNET_MASK—Subnet mask for the router you are using.
DEFAULT_GATEWAY—Default gateway for the router you are using (not required if the TFTP server is in the same subnet as the router).
TFTP_SERVER—IP address of the server from which you want to download the image file.
TFTP_FILE—Name of the file that you want to download.

For example:

rommon 1> IP_ADDRESS=172.15.19.11
rommon 2> IP_SUBNET_MASK=255.255.255.0
rommon 3> DEFAULT_GATEWAY=172.16.19.1
rommon 4> TFTP_SERVER=172.15.20.10
rommon 5> TFTP_FILE=c3620-i-mz.120-4.T

Once you set the above variables, you can type the tftpdnld command and press "y" to proceed:

rommon 6>tftpdnld
Do you wish to continue? y/n: y

Make sure you have your TFTP server running and the previous image in the root of the TFTP server's folder.

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis2600/hw_inst/2600hig/2600appb.htm#1042476

0

Featured Post

[Webinar] Learn How Hackers Steal Your Credentials

Do You Know How Hackers Steal Your Credentials? Join us and Skyport Systems to learn how hackers steal your credentials and why Active Directory must be secure to stop them. Thursday, July 13, 2017 10:00 A.M. PDT

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

While it is possible to put two routes in place with the secondary having a higher metric, this may not always work. In the event of a failure that does not bring down the physical interface on the router the primary route is not removed. There is a…
In this tutorial I will show you with short command examples how to obtain a packet footprint of all traffic flowing thru your Juniper device running ScreenOS. I do not know the exact firmware requirement, but I think the fprofile command is availab…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses

705 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question