Solved

Contivity 100 Port Forwarding

Posted on 2004-08-03
6
896 Views
Last Modified: 2013-11-21
I need help setting up port forwarding to allow remote desktop connections across the Nortel Contivity 100 NAT that we use.
I need specific help finding the syntax of the commands used in this NAT box.

The contivity 100 uses Baystack Instant Internet 7.20

Any help would be great.

Thanks.
0
Comment
Question by:straterpatrick
  • 3
  • 3
6 Comments
 
LVL 8

Expert Comment

by:MarkDozier
Comment Utility
This is athe link to the confguration guide
http://www116.nortelnetworks.com/docs/bvdoc/contivity/doc_pdf/315896C00.pdf

NAT begins on Pg 71. Your device uses a wizard so after reading the chapter on NAT you should be just fine.
0
 

Author Comment

by:straterpatrick
Comment Utility
Hmmm... I get a Access Denied when I try to access this link.
I don't think this is the right document anyways. This device does not have a wizard of any kind. You may be thinking of the contivity configuration manager which you have to buy and I dont even think they sell it anymore. (Contivity devices were phased out a while ago.)

I'm looking for help with the config file this box uses. Here is the current one if that helps:

dns suffix instant.net
encapsulation aux terminal
name XXXX
ifconfig eth1 ipaddress 10.170.150.1 255.255.255.0
dhcp configure eth3
ifconfig eth3 xlate out
hostname eth3
ip forwarding on
route add default eth3
route add 10.180.1.0/24 eth1 10.180.150.2
route add 192.57.43.34/32 eth1 10.180.150.2
route add 192.57.43.65/32 eth1 10.180.150.2
route add 204.104.220.0/24 eth1 10.180.150.2
route add 205.239.188.15/32 eth1 10.180.150.2
dnsproxyd start
identd start
snmpd start
socksd start
tcpserver
telnetd start
webproxy start
webserver start

I think for port forwarding you need to add infilters but I can't seem to find the right syntax.
0
 
LVL 8

Expert Comment

by:MarkDozier
Comment Utility
I got the link by going to
http://www.nortelnetworks.com/products/01/contivity/100/
then clciking on the Techincal Spec link on the right hand side

Eveything i have seen on this device shows using a web interface for configuration. Have you tried using that?

0
Why You Should Analyze Threat Actor TTPs

After years of analyzing threat actor behavior, it’s become clear that at any given time there are specific tactics, techniques, and procedures (TTPs) that are particularly prevalent. By analyzing and understanding these TTPs, you can dramatically enhance your security program.

 

Author Comment

by:straterpatrick
Comment Utility
It does have a web configuration page but it simply lets me edit the config file as shown above.

The web interface is baystack instant internet 7.20
0
 
LVL 8

Accepted Solution

by:
MarkDozier earned 500 total points
Comment Utility
0
 

Author Comment

by:straterpatrick
Comment Utility
I am still having problems getting it to work but the documentation has helped a lot. One of the biggest problems is that I am missing the software that came with the device.

I contacted the suplier and they are shipping me the configuration software (Contivity branch access 7.20) tomorrow. Hopefully that will help.

Thank you Mark. I will accept your answer and if I have more problems I will list another question.

Thanks!
0

Featured Post

Do You Know the 4 Main Threat Actor Types?

Do you know the main threat actor types? Most attackers fall into one of four categories, each with their own favored tactics, techniques, and procedures.

Join & Write a Comment

Suggested Solutions

What’s a web proxy server? A proxy server is a server that goes between clients and web servers, used in corporate to enforce corporate browsing policy and ensure security. Proxy servers are commonly used in three modes. A)    Forward proxy …
Join Greg Farro and Ethan Banks from Packet Pushers (http://packetpushers.net/podcast/podcasts/pq-show-93-smart-network-monitoring-paessler-sponsored/) and Greg Ross from Paessler (https://www.paessler.com/prtg) for a discussion about smart network …
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Get a first impression of how PRTG looks and learn how it works.   This video is a short introduction to PRTG, as an initial overview or as a quick start for new PRTG users.

763 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

6 Experts available now in Live!

Get 1:1 Help Now