Solved

Dlink Router DI-808HV

Posted on 2004-08-28
2
416 Views
Last Modified: 2008-01-09
Hello,

Trying to set up a VPN between two of these routers, I show the routers are connected in the status screen, but when I attempt to ping the a computer on the host side I get nothing.

Settings for the Remote Side !
 
VPN Settings - Tunnel 1

       Item Setting
Tunnel Name  remote1
Aggressive Mode  Enable - yes
Local Subnet  - 192.168.0.1
Local Netmask - 255.255.255.0
Remote Subnet  - 10.251.83.0
Remote Netmask  - 255.255.255.0
Remote Gateway  24.227.112.214
Preshare Key   joshua
ID Proposal Name DH Group Encrypt algorithm Auth algorithm Life Time Life Time Unit
1   Group 1Group 2Group 5  3DESDES  SHA1MD5   Sec.Kbyte
ID Proposal Name DH Group Encap protocol Encrypt algorithm Auth algorithm Life Time Life Time Unit
1  NoneGroup 1Group 2Group 5 ESPAH 3DESDES SHA1MD5None  

Host side setup !

VPN Settings - Tunnel 1

       Item Setting
Tunnel Name  - remote1
Aggressive Mode - yes
Local Subnet  10.251.83.0
Local Netmask  255.255.255.0
Remote Subnet  192.168.0.1
Remote Netmask  255.255.255.0
Remote Gateway  68.202.228.8
Preshare Key   joshua
IKE Proposal index  
IPSec Proposal index  

any thoughts on this and what may not be allowing me to ping the host network ? Below is the status the router's both show
Name Remote Network Local Network Type State Life
Time Drop
IP Address/
Subnet Mask/
Gateway IP Address/
Subnet Mask
remote1 192.168.0.1/
255.255.255.0/
68.202.228.8 10.251.83.0/
255.255.255.0 ESP tunnel IKE established 149790  

Thanks for your help in advance
Tony G


   
   
0
Comment
Question by:tonyg01
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
2 Comments
 
LVL 15

Accepted Solution

by:
plimpias earned 500 total points
ID: 11924543
Upgrade the firmware on both of your routers. There is a known problem with this
0
 

Author Comment

by:tonyg01
ID: 11946596
This was done on both ends from the beginning, the solution was adding the pppt virtual server option in the router ( 5 hours with DLINK support and four case numbers ) wow !

Thanks for your help
0

Featured Post

Portable, direct connect server access

The ATEN CV211 connects a laptop directly to any server allowing you instant access to perform data maintenance and local operations, for quick troubleshooting, updating, service and repair.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
unable to set full duplex 100 on WAN interface 11 101
Port Forwarding 4 62
Network over eigrp 100 topology ? 3 93
Need to cut my Verizon home cost 3 66
In the hope of saving someone else's sanity... About a year ago we bought a Cisco 1921 router with two ADSL/VDSL EHWIC cards to load balance local network traffic over the two broadband lines we have, but we couldn't get the routing to work consi…
Tired of waiting for your show or movie to load?  Are buffering issues a constant problem with your internet connection?  Check this article out to see if these simple adjustments are the solution for you.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

752 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question