Solved

VLAN setup (need help, almost done)

Posted on 2004-09-10
4
273 Views
Last Modified: 2010-04-17
Ok, I have a 2924 switch and a 2612 router. Trying to implement a VLAN here.

So far I've:
Made port 0/4 on the switch part of  VLAN2.
Made port 24 on the switch the trunk link

I went to the 2600 router and did a

c2600(config)#int e0/0.1
c2600(config-subif)#encapsulation dot1q
Invalid Input detected  ^

It seems the encapsulation command is not working.  I am running 12.3(9) IOS on the 2612 router.   I know that this router supports 802.1q encapsulation as stated here by Cisco http://www.cisco.com/en/US/products/hw/routers/ps259/prod_bulletin09186a00800921e4.html
Help! I even downgrade my IOS to c2600-io3-mz.122-23  and still nothing?
Help
Thanks


0
Comment
Question by:dissolved
  • 2
  • 2
4 Comments
 
LVL 7

Accepted Solution

by:
pedrow earned 500 total points
ID: 12033282
methinks you'll need to have at least the ip plus feature set in order to get vlan support.

the 'downgrade' image you've got is  IP/FW/IDS which might not include the 'plus' features.

The  'plus' features are included in images with an 's' in them, such as:

 c2600-is-mz ( IP PLUS)

or
 c2600-ik9s-mz ( IP PLUS IPSEC 3DES)
0
 

Author Comment

by:dissolved
ID: 12033939
How would I go about getting these images for educational/personal use???
0
 

Author Comment

by:dissolved
ID: 12034409
WOW, nevermind. I just found out I have to buy it and it costs 3 times the price of the router! lol.
Oh well :-(

Thanks pedrow for the info my man
0
 
LVL 7

Expert Comment

by:pedrow
ID: 12035707
np...
at least the answer was cheap, if not the solution... :-/

0

Featured Post

PRTG Network Monitor: Intuitive Network Monitoring

Network Monitoring is essential to ensure that computer systems and network devices are running. Use PRTG to monitor LANs, servers, websites, applications and devices, bandwidth, virtual environments, remote systems, IoT, and many more. PRTG is easy to set up & use.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

We've been using the Cisco/Linksys RV042 for years as: - an internet Gateway - a site-to-site VPN device - a leased line site-to-site subnet-to-subnet interface (And, here I'm assuming that any RV0xx behaves the same way as an RV042.  So that's …
There are two basic ways to configure a static route for Cisco IOS devices. I've written this article to highlight a case study comparing the configuration of a static route using the next-hop IP and the configuration of a static route using an outg…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

829 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question