Solved

t1 setup w/ 2610

Posted on 2004-09-19
3
208 Views
Last Modified: 2010-04-17
Hello,

I have a cisco 2610 with a WIC-1DSU-t1.  My ISP says the following:

Channels: 12
LMI: Ansi
Encaspulation: Frame relay
DLCI: 16
username: ***
password: ***
CHAP

could any help me set up the internet on my router?
0
Comment
Question by:mark2m60
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
3 Comments
 
LVL 79

Accepted Solution

by:
lrmoore earned 500 total points
ID: 12097791
Frame Relay does not use username/password or CHAP.
!
interface Ethernet 0/0
  ip address 192.168.123.1 255.255.255.0  <== whatever your internal LAN is
  description Local LAN
  no shutdown
  ip nat inside
!
interface serial 0/0
  description T1 to ISP
  no shutdown
  no cdp enable
  encapsulation frame-relay
  service-module t1 timeslots 1-12
  frame-relay lmi-type ansi
!
interface serial 0/0.1 point-to-point
  description T1 frame-relay sub-interface
  ip address 4.5.6.7 255.255.255.248  <== whatever the ISP assigned you for IP
  frame-relay interface-dlci 16
  ip nat outside
!
ip route 0.0.0.0 0.0.0.0 4.5.6.8  <== whatever the ISP gave you as a default gateway
!
ip nat inside source list 1 interface serial0/0.1 overload
access-list 1 permit 192.168.123.0 0.0.0.255
!

Done!
At least the basics are done and you should be able to communicate.

Testing:
  router# show frame-relay pvc  -- look for: DLCI 16  ACTIVE  Serial 0/0.1
  router# show interface serial 0/0  -- look for Serial 0/0 is up, line protocol is up
  router# show interface serial 0/0.1 -- look for line up, protocol up condition

0
 
LVL 79

Expert Comment

by:lrmoore
ID: 12105668
Are you still working this? Any luck?
0
 

Author Comment

by:mark2m60
ID: 12129555
Thanks for the config - I was able to get the router in an up/up state however my ISP does not allow any unauthenticated traffic through their network.  I had to use a virtual template interface to allow chap auth.  Thank you very much though

0

Featured Post

Free Tool: IP Lookup

Get more info about an IP address or domain name, such as organization, abuse contacts and geolocation.

One of a set of tools we are providing to everyone as a way of saying thank you for being a part of the community.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Line cards, Supervisor, Control plane 7 61
Is WiFi half-duplex or Full -duplex 4 67
Network Vs Redistribute Connected Commands 3 64
Extended ping 6 31
In the hope of saving someone else's sanity... About a year ago we bought a Cisco 1921 router with two ADSL/VDSL EHWIC cards to load balance local network traffic over the two broadband lines we have, but we couldn't get the routing to work consi…
The Cisco RV042 router is a popular small network interfacing device that is often used as an internet gateway. Network administrators need to get at the management interface to make settings, change passwords, etc. This access is generally done usi…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

726 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question