Solved

Connect Two Cisco Routers using SHDSL-V2 WICS

Posted on 2004-09-27
4
406 Views
Last Modified: 2008-03-03
I have two Cisco 3745 routers and I wish to connect these two routers via an analogue lease line using SHDSL-V2 WICS. (Head Office to Remote Branch) We have been succesfull in testing communication over this 4 wire analogue line using 2 SDSL modems and have got up to 2mb line speeds. (Hopefully we can even get up to 4mb lines speeds). I would like to be able to route both data and voice packets across this line.

Could someone please provide me with a working configuration for both Cisco routers?

Thank you.

Jeshurun
0
Comment
Question by:Jeshurun
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
4 Comments
 
LVL 5

Accepted Solution

by:
netspec01 earned 500 total points
ID: 12190014
Here is a very basic router config.  It assumes that you are using a serial interface, campus environment vs. Internet, that your ISP is providing a fixed IP address and that you don't have to authenticate to your ISP.  I'm not sure how the SHDSL-V2 WICS shows up in your configuration.

- If the connection is to the Internet rather than a campus environment, you will need to have VPN capable software and set up a VPN tunnel between the two sites.

- If authentication is needed you will need a "dialer" configuration added to do the authentication to the ISP

- If there are other routers/Internet connections, additional routing will be required.

Send more information on the connection type and what the ISP provided you.

Very basic router configuration:

hostname myrouter
!
enable secret xxxx
!
ip subnet-zero
!
interface serial0/0
 ip address w.x.y.z  255.255.255.252   ! ISP provides this
!
ip unnumbered FastEthernet0/0  ! need different networks for each site
 ip address 10.0.0.0 255.255.255.0
!
ip route 0.0.0.0 0.0.0.0 a.b.c.d  ! ISP provides this as gateway address or next-hop router
!
line con 0
 password xxxx
line aux 0
 password xxxx
line vty 0 4
 password xxxx
!
end
0
 
LVL 5

Expert Comment

by:netspec01
ID: 12280603
Are you still working on this?  Can you close this question?
0

Featured Post

Save the day with this special offer from ATEN!

Save 30% on the CV211 using promo code EXPERTS30 now through April 30th. The ATEN CV211 connects a laptop directly to any server allowing you instant access to perform data maintenance and local operations, for quick troubleshooting, updating, service and repair.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Line cards, Supervisor, Control plane 7 66
Cisco 3650 switch 1G port to 10G port 6 40
Routers to buy for MDT Multitasking 6 75
wifi security 11 41
We've been using the Cisco/Linksys RV042 for years as: - an internet Gateway - a site-to-site VPN device - a leased line site-to-site subnet-to-subnet interface (And, here I'm assuming that any RV0xx behaves the same way as an RV042.  So that's …
In the world of WAN, QoS is a pretty important topic for most, if not all, networks. Some WAN technologies have QoS mechanisms built in, but others, such as some L2 WAN's, don't have QoS control in the provider cloud.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

737 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question