Solved

VNCServer - Starting up on boot

Posted on 2004-09-28
9
709 Views
Last Modified: 2010-04-20
Alright here is some background.  We have 2 dell poweredge servers running RedHat ES3 on them, and they will be running Oracle software.  They will be put in a different building as soon as I figure this out.

I have vncserver running correctly on the 2 servers, and we can access them just fine.  The problem is that when we reboot the server you can not access VNCserver until you log into the server.  This means that you physically have to be at the server.

How can we get VNCserver to start up for 2 users when the computer starts up?  or what kind of workaround is there for this type of problem?
0
Comment
Question by:Intern
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 6
  • 3
9 Comments
 
LVL 6

Accepted Solution

by:
knollbert earned 500 total points
ID: 12171232
0
 
LVL 1

Author Comment

by:Intern
ID: 12171589
I added this line to the vncserver file

VNCSERVERS="1:oracle"

And when I run "/etc/init.d/vncserver start" it starts up the vncserver session correctly.  Then I added the following line to 'usr/share/doc/pam_krb5-1.73/pam.d/linuxconf' , 'usr/share/doc/pam_krb5-1.73/krb5afs-pam.d/linuxconf', and 'usr/share/doc/nss_ldap-207/pam.d/linuxconf'

account        required     /etc/init.d/vncserver start

It does not start up when the server starts.  What am I doing wrong?
0
 
LVL 6

Expert Comment

by:knollbert
ID: 12171678
did you add the correct link to your
/etc/rc.d/rd.3 folder (may not be right it been a while)
0
Complete VMware vSphere® ESX(i) & Hyper-V Backup

Capture your entire system, including the host, with patented disk imaging integrated with VMware VADP / Microsoft VSS and RCT. RTOs is as low as 15 seconds with Acronis Active Restore™. You can enjoy unlimited P2V/V2V migrations from any source (even from a different hypervisor)

 
LVL 1

Author Comment

by:Intern
ID: 12171732
little clarification please -

I found the folder, but what am I supposed to put there? or what file should I modify?
0
 
LVL 6

Expert Comment

by:knollbert
ID: 12171820
like i said its been awhile since i've used RH but try
ln -s /etc/rc.d/init.d/vncserver /etc/rc.d/rc3.d/S79vncserver

ln -s /etc/rc.d/init.d/vncserver /etc/rc.d/rc2.d/k79vncserver
0
 
LVL 6

Expert Comment

by:knollbert
ID: 12171836
ln -s /etc/rc.d/init.d/vncserver /etc/rc.d/rc0.d/k79vncserver
ln -s /etc/rc.d/init.d/vncserver /etc/rc.d/rc1.d/k79vncserver
ln -s /etc/rc.d/init.d/vncserver /etc/rc.d/rc6.d/k79vncserver


too
0
 
LVL 1

Author Comment

by:Intern
ID: 12172328
Works great!!!! Thank you very much.  By the way if you know Samba, I have another question out there.

http://www.experts-exchange.com/Operating_Systems/Linux/Q_21148254.html
0
 
LVL 6

Expert Comment

by:knollbert
ID: 12172689
I Know a little about many things I'll look
0
 
LVL 6

Expert Comment

by:knollbert
ID: 12172694
Just enough to be dangerous
0

Featured Post

Technology Partners: We Want Your Opinion!

We value your feedback.

Take our survey and automatically be enter to win anyone of the following:
Yeti Cooler, Amazon eGift Card, and Movie eGift Card!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Over the last ten+ years I have seen Linux configuration tools come and go. In the early days there was the tried-and-true, all-powerful linuxconf that many thought would remain the one and only Linux configuration tool until the end of times. Well,…
It’s 2016. Password authentication should be dead — or at least close to dying. But, unfortunately, it has not traversed Quagga stage yet. Using password authentication is like laundering hotel guest linens with a washboard — it’s Passé.
Learn how to get help with Linux/Unix bash shell commands. Use help to read help documents for built in bash shell commands.: Use man to interface with the online reference manuals for shell commands.: Use man to search man pages for unknown command…
Learn how to navigate the file tree with the shell. Use pwd to print the current working directory: Use ls to list a directory's contents: Use cd to change to a new directory: Use wildcards instead of typing out long directory names: Use ../ to move…

705 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question