Solved

setting services problem

Posted on 2004-10-10
1
235 Views
Last Modified: 2013-12-16
Below is my log of services on my Pc redhat 9:-

usage: aep1000 [start|stop|restart|condrestart]
anacron (pid 1235) is running...
atd (pid 1244) is running...
Configured Mount Points:
------------------------

Active Mount Points:
--------------------
BCM5820 driver not loaded.
crond (pid 1135) is running...
cupsd (pid 1146) is running...
gpm (pid 1126) is running...
httpd is stopped
Table: filter
Chain INPUT (policy ACCEPT)
target     prot opt source               destination        
RH-Lokkit-0-50-INPUT  all  --  anywhere             anywhere          

Chain FORWARD (policy ACCEPT)
target     prot opt source               destination        
RH-Lokkit-0-50-INPUT  all  --  anywhere             anywhere          

Chain OUTPUT (policy ACCEPT)
target     prot opt source               destination        

Chain RH-Lokkit-0-50-INPUT (2 references)
target     prot opt source               destination        
ACCEPT     udp  --  10.0.0.1             anywhere           udp spt:domain dpts:1025:65535
ACCEPT     tcp  --  anywhere             anywhere           tcp dpt:http flags:SYN,RST,ACK/SYN
ACCEPT     tcp  --  anywhere             anywhere           tcp dpt:ftp flags:SYN,RST,ACK/SYN
ACCEPT     tcp  --  anywhere             anywhere           tcp dpt:telnet flags:SYN,RST,ACK/SYN
ACCEPT     udp  --  anywhere             anywhere           udp spts:bootps:bootpc dpts:bootps:bootpc
ACCEPT     udp  --  anywhere             anywhere           udp spts:bootps:bootpc dpts:bootps:bootpc
ACCEPT     all  --  anywhere             anywhere          
ACCEPT     all  --  anywhere             anywhere          
REJECT     tcp  --  anywhere             anywhere           tcp dpts:0:1023 flags:SYN,RST,ACK/SYN reject-with icmp-port-unreachable
REJECT     tcp  --  anywhere             anywhere           tcp dpt:nfs flags:SYN,RST,ACK/SYN reject-with icmp-port-unreachable
REJECT     udp  --  anywhere             anywhere           udp dpts:0:1023 reject-with icmp-port-unreachable
REJECT     udp  --  anywhere             anywhere           udp dpt:nfs reject-with icmp-port-unreachable
REJECT     tcp  --  anywhere             anywhere           tcp dpts:x11:6009 flags:SYN,RST,ACK/SYN reject-with icmp-port-unreachable
REJECT     tcp  --  anywhere             anywhere           tcp dpt:xfs flags:SYN,RST,ACK/SYN reject-with icmp-port-unreachable
irattach is stopped
No status available for this package
lisa is stopped
Configured devices:
lo eth0
Currently active devices:
lo eth0
rpc.mountd is stopped
nfsd is stopped
rpc.rquotad is stopped
rpc.statd (pid 977) is running...
nscd is stopped
ntpd is stopped
portmap (pid 958) is running...
pxe is stopped
The random data source exists
saslauthd is stopped
sendmail (pid 1116 1107) is running...
smbd is stopped
nmbd is stopped
snmpd is stopped
snmptrapd is stopped
squid is stopped
sshd (pid 1073) is running...
syslogd (pid 936) is running...
klogd (pid 940) is running...
tux is stopped
vsftpd is stopped
winbindd is stopped
xfs (pid 1226) is running...
xinetd (pid 1087) is running...
ypbind is stopped
rpc.yppasswdd is stopped
ypserv is stopped
rpc.ypxfrd is stopped
>>>>above is output i redirected from service --status-all to this text file but it give some error messages also and they are:->>>

FATAL: Could not determine fully qualified hostname.  Please set 'visible_hostname'

Squid Cache (Version 2.5.STABLE1): Terminated abnormally.
CPU Usage: 0.010 seconds = 0.010 user + 0.000 sys
Maximum Resident Size: 0 KB
Page faults with physical i/o: 402
/etc/init.d/squid: line 162:  1881 Aborted                 $SQUID -k check

>>>what are the problems in my configuration to linux installation?

0
Comment
Question by:panemade
1 Comment
 
LVL 17

Accepted Solution

by:
owensleftfoot earned 50 total points
ID: 12274678
Squid cant determine your fully qualified domain name - probably because you dont have one. Edit /etc/squid/squid.conf and add a line
visible_hostname  myhostname.com

where myhostname.com is the domainname you want to give  squid.
0

Featured Post

Highfive Gives IT Their Time Back

Highfive is so simple that setting up every meeting room takes just minutes and every employee will be able to start or join a call from any room with ease. Never be called into a meeting just to get it started again. This is how video conferencing should work!

Join & Write a Comment

Daily system administration tasks often require administrators to connect remote systems. But allowing these remote systems to accept passwords makes these systems vulnerable to the risk of brute-force password guessing attacks. Furthermore there ar…
SSH (Secure Shell) - Tips and Tricks As you all know SSH(Secure Shell) is a network protocol, which we use to access/transfer files securely between two networked devices. SSH was actually designed as a replacement for insecure protocols that sen…
Learn how to find files with the shell using the find and locate commands. Use locate to find a needle in a haystack.: With locate, check if the file still exists.: Use find to get the actual location of the file.:
Learn how to navigate the file tree with the shell. Use pwd to print the current working directory: Use ls to list a directory's contents: Use cd to change to a new directory: Use wildcards instead of typing out long directory names: Use ../ to move…

744 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

14 Experts available now in Live!

Get 1:1 Help Now