asked on

ChiliASP and port 5100 access

Hi,

I have RHEL installed and Chili ASP server installed:

Still, when I launch up my firefox and plug in this url:

http://localhost:5100

I get the following error: "The connection was refused when attempting to contact localhost:5100

I dont understand if this is an apache config or a linux firewall issue

Any ideas please?

Thanks

Leo Eikelman

I don't have too much knowledge in this field but try running a port scan using

nmap -v devicename

and check that the port is open/available

Also you might want to check if you have access to annonymous logins.

Leo

niftyhawk

ASKER

Hi,
Following is the result of the nmap scan.

What do I do now??

Starting nmap 3.70 ( http://www.insecure.org/nmap/ ) at 2006-04-04 12:24 CDT
Initiating SYN Stealth Scan against vrhat2 (127.0.0.1) [1660 ports] at 12:24
Discovered open port 25/tcp on 127.0.0.1
Discovered open port 22/tcp on 127.0.0.1
Discovered open port 443/tcp on 127.0.0.1
Discovered open port 80/tcp on 127.0.0.1
Discovered open port 113/tcp on 127.0.0.1
Discovered open port 10000/tcp on 127.0.0.1
Discovered open port 111/tcp on 127.0.0.1
Discovered open port 445/tcp on 127.0.0.1
Discovered open port 631/tcp on 127.0.0.1
Discovered open port 139/tcp on 127.0.0.1
Discovered open port 1521/tcp on 127.0.0.1
The SYN Stealth Scan took 0.26s to scan 1660 total ports.
Host vrhat2 (127.0.0.1) appears to be up ... good.
Interesting ports on vrhat2 (127.0.0.1):
(The 1649 ports scanned but not shown below are in state: closed)
PORT STATE SERVICE
22/tcp open ssh
25/tcp open smtp
80/tcp open http
111/tcp open rpcbind
113/tcp open auth
139/tcp open netbios-ssn
443/tcp open https
445/tcp open microsoft-ds
631/tcp open ipp
1521/tcp open oracle
10000/tcp open snet-sensor-mgmt

Nmap run completed -- 1 IP address (1 host up) scanned in 0.474 seconds

Thanks,

Leo Eikelman

Well as you can see the port you specified is not open/available.

Again, I'm not an expert on this, but is SWAT running?

And if it is running, are you accessing from the machine that SWAT is running on or from a machine on the network.

Check the config file in xinetd.d again. Does it say something like:
only_from = localhost
That means you can only access swat from the PC its running on.

also check xinetd.d and check the following line

disable = no

is set to no.

I got this information by goggling your problem so I have not tested any of these suggestions.

Leo

niftyhawk

ASKER

I fixed that file accordingly.. still doesnt work.. Any more ideas?

Leo Eikelman

I will do some more digging once I get some more time today.

Meanwhile, if anyone else reads this thread. The port niftyhawk is trying to reach is not open/available. If anyone knows how to make it open/available then let him know please.

Leo

niftyhawk

ASKER

I resolved this, by commenting two lines (the LoadModule xmlbody_module handler and Add Handler ) in /usr/casp/admin/conf/admd.conf

I am able to go to the administration panel now.

Now, I hit with the drivers issue. When I go to Server Management-> Drivers page, I get ODBC errors..

SQLState: IM003 Native Error Code:80 Specified driver could not be loaded

I am running oracle 9i on RHEL. How can I fix this??

Thanks Leo for trying !!

ASKER CERTIFIED SOLUTION

GranMod

membership

This solution is only available to members.

To access this solution, you must be a member of Experts Exchange.

Start Free Trial