Solved

Need urgent help with Cisco 1841 route connecting the Ethernet ports to 2 routers and routing traffic

Posted on 2006-06-10
5
346 Views
Last Modified: 2013-11-29
Hello,

I am having some serious issues with a router configuration on a 1841.
We have 2 routers from our ISP.
The first one is providing a T1 connection
The second one is providing a connection to a frame relay network
All the encapsulation is done on the ISP's routers.
All users connect to the ethernet interface 0/1 of the cisco router.
Then there traffic should be routet to the Frame, if they are accessing resources in a secondary location, or should be routet to the T1 router for Internet traffic.
The 1841 has two build in ethernet ports, and we purchased a HWIC - 4ESW
(4 port Ethernet switch)
eth port 0/0 is connected to the frame relay router 192.168.1.254
eth port 0/1 is connected to the local network 192.168.3.1
port for on the HWIC is connected to the T1 router  ***.***.***.209

int FastEthernet0/0  192.168.1.1
int FastEthernet0/1 192.168.3.1
int FastEthernet0/1/3  ***.***.***.210

I have configured static routes that look something like this.
ip route 192.168.3.0  255.255.255.0 192.168.1.254
ip route 192.168.3.0  255.255.255.248   ***.***.***.209 (T1 connection)
ip route  ***.***.***.0  255.255.255.248 ***.***.***.209

all interfaces are up

I can ping the 192.168.1.254 ip address which is the address of the router which handels the frame relay connection. I can also ping the router at the other end of the frame relay 192.168.2.1

I can ping the Interface of the router which handels the T1 ***.***.***.209
but I can not ping any IP address on the internet.
DNS has been setup as well.

I have dhcp configured for the 192.168.3.0 network.
My workstations receive a ip address in that range via dhcp, and can ping the interface 192.168.3.1
but can not ping the T1 router or the frame router.

Any help would be really really appreciated.
A sample would be great too.

Thanks alot

Drew

0
Comment
Question by:quasimodo1
5 Comments
 
LVL 10

Expert Comment

by:naveedb
ID: 16879349
Assuming 1841 is the third router; the other two are from ISP

                       INTERNET ROUTER-->INTERNET
LAN--> 1841 <
                       FRAME-RELAY ROUTER--> OTHER LOCATION
Can you post output from the following;

show ip int br
show ip route
0
 
LVL 1

Expert Comment

by:mohai
ID: 16883846
from the static route that you provided, i dont see and default gateway for network 0.0.0.0 mask 0.0.0.0
Just wondering if you have forgotten this one.
0
 

Author Comment

by:quasimodo1
ID: 16964346
I apologize for the late response.
I figured out the problem, NAT was not configured for the LAN interface.
After configuring NAT it worked fine.

Thank you for your replies.

Andrew


0
 

Accepted Solution

by:
ee_ai_construct earned 0 total points
ID: 17296897
PAQ / Refund
ee ai construct, community support moderator
0

Featured Post

Netscaler Common Configuration How To guides

If you use NetScaler you will want to see these guides. The NetScaler How To Guides show administrators how to get NetScaler up and configured by providing instructions for common scenarios and some not so common ones.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Claiming a Domain Name 7 52
Guest Wireless in a Business Environment 6 90
Client lost connection to AP controlled by Cisco WLC2504 3 38
FTP Transfer Speeds ... 6 53
If your business is like most, chances are you still need to maintain a fax infrastructure for your staff. It’s hard to believe that a communication technology that was thriving in the mid-80s could still be an essential part of your team’s modern I…
When you try to share a printer , you may receive one of the following error messages. Error message when you use the Add Printer Wizard to share a printer: Windows could not share your printer. Operation could not be completed (Error 0x000006…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Here's a very brief overview of the methods PRTG Network Monitor (https://www.paessler.com/prtg) offers for monitoring bandwidth, to help you decide which methods you´d like to investigate in more detail.  The methods are covered in more detail in o…

840 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question