?
Solved

Cisco router 803 ping issue

Posted on 2006-06-12
2
Medium Priority
?
374 Views
Last Modified: 2006-11-18
Hi there

I have an old Cisco 803 router and I'd like to backup the IOS to a TFTP server as practise.

I am accessing the router via Hyperterminal console on a PC. A laptop, which I am going to use as the TFTP server, is connected to the e0 interface of the router.

The laptop has been assigned as static IP address of 192.168.1.65/24.  The e0 interface on the router has been assigned an IP address of 192.168.1.66/24, and they are connected via x-over cable.

Strangely, I can ping 192.168.1.66 from the laptop, but cannot ping 192.168.1.65 from the router.

Config posted below>>>

Router1#sh run
no service password-encryption
!
hostname Router1
!
!
!
ip subnet-zero
!
!
!
!
interface Ethernet0
 ip address 192.168.1.66 255.255.255.0
 no ip directed-broadcast
!
interface BRI0

>>> show version below

IOS (tm) C800 Software (C800-G3-MW), Version 12.0(3)T1,  RELEASE SOFTWARE (fc1)

Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Mon 08-Mar-99 15:10 by cmong
Image text-base: 0x000E9000, data-base: 0x0053D000

ROM: TinyROM version 1.2(2)
Router1 uptime is 1 hour, 28 minutes
System restarted by power-on
System image file is "flash:c800-g3-mw.120-3.T1"

Cisco C803 (MPC850) processor (revision 1) with 43512K bytes of virtual memory.
Processor board ID JAD04082OIS
CPU part number 33
Bridging software.
Basic Rate ISDN software, Version 1.1.
1 Ethernet/IEEE 802.3 interface(s)
1 ISDN Basic Rate interface(s)
4M bytes of physical memory (DRAM)
8K bytes of non-volatile configuration memory
8M bytes of flash on board (4M from flash card)

Configuration register is 0x2102

Is there anything glaringly obvious that I'm doing wrong?

Thanks
0
Comment
Question by:Dilan77
2 Comments
 
LVL 50

Accepted Solution

by:
Don Johnston earned 1000 total points
ID: 16885735
Most likely, if you're running XP, the firewall feature is blocking ICMP echo requests. You can go into network properties and permit it if you want.
0
 
LVL 2

Author Comment

by:Dilan77
ID: 16885790
Cheers - it was the Windows firewall blocking ICMP.
0

Featured Post

The 14th Annual Expert Award Winners

The results are in! Meet the top members of our 2017 Expert Awards. Congratulations to all who qualified!

Question has a verified solution.

Are you are experiencing a similar issue? Get a personalized answer when you ask a related question.

Have a better answer? Share it in a comment.

Join & Write a Comment

Hello , This is a short article on how would you go about enabling traceoptions on a Juniper router . Traceoptions are similar to Cisco debug commands but these traceoptions are implemented in Juniper networks router . The following demonstr…
We've been using the Cisco/Linksys RV042 for years as: - an internet Gateway - a site-to-site VPN device - a leased line site-to-site subnet-to-subnet interface (And, here I'm assuming that any RV0xx behaves the same way as an RV042.  So that's …
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

568 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question