Solved

PIX 525 OS upgrade error (Not enough space on device)

Posted on 2006-06-13
2
2,218 Views
Last Modified: 2013-11-16
I have a new 525, I went through the steps to upgrade OS 6.3 to 7.04. When I do the final step according to the upgrade guide (shown at "Guide Instructions" below) this what the output is, I get not enough space error. How to resolve this?

CONSOLE OUTPUT:

WWR-FW-1(config)# copy tftp://192.168.6.5/cisco/os/pix704.bin flash:

Address or name of remote host [192.168.6.5]?

Source filename [cisco/os/pix704.bin]?

Destination filename [pix704.bin]?

Accessing tftp://192.168.6.5/cisco/os/pix704.bin...!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!
%Error copying tftp://192.168.6.5/cisco/os/pix704.bin (Not enough space on devic
e)



GUIDE INSTRUCTIONS:

To save the PIX Security appliance Version 7.0 image to Flash from global configuration mode, perform the following steps:

a. Copy the PIX Security appliance Version 7.0 image from the TFTP server using the following commands. (This requires you to configure an IP address on the security appliance interface that connects to the TFTP server.)

PIX(config)#interface ethernet 0
PIX(config-if)# ip address 20.0.0.10 255.255.255.0
copy tftp [:[[//location] [/tftp_pathname]]] flash[:[image | pdm]]
PIX(config)# copy tftp://20.0.0.101/pix704.bin flash:
The following set of TFTP prompts results from the preceding command:

Address or name of remote host [20.0.0.101]?
Source filename [pix704.bin]?
Destination filename [pix704.bin]?


--------------------------------------------------------------------------------

Note Multiple lines referring to invalid Flash blocks will be printed while the Flash is reformatted, which is normal.

Your PIX Version 6.3 configuration will be saved as downgrade.cfg in PIX Security appliance Version 7.0.
0
Comment
Question by:questfar
2 Comments
 
LVL 79

Accepted Solution

by:
lrmoore earned 500 total points
ID: 16894005
You might have to remove 6.3 image first
dir flash:
delete flash:pix63x.bin
   or
delete flash:image.bin
You might also have to delete the PDM folder
0
 

Author Comment

by:questfar
ID: 16907782
that did it , thanks
0

Featured Post

PRTG Network Monitor: Intuitive Network Monitoring

Network Monitoring is essential to ensure that computer systems and network devices are running. Use PRTG to monitor LANs, servers, websites, applications and devices, bandwidth, virtual environments, remote systems, IoT, and many more. PRTG is easy to set up & use.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

This article will cover setting up redundant ISPs for outbound connectivity on an ASA 5510 (although the same should work on the 5520s and up as well).  It’s important to note that this covers outbound connectivity only.  The ASA does not have built…
For months I had no idea how to 'discover' the IP address of the other end of a link (without asking someone who knows), and it drove me batty. Think about it. You can't use Cisco Discovery Protocol (CDP) because it's not implemented on the ASAs.…
As a trusted technology advisor to your customers you are likely getting the daily question of, ‘should I put this in the cloud?’ As customer demands for cloud services increases, companies will see a shift from traditional buying patterns to new…
Both in life and business – not all partnerships are created equal. Spend 30 short minutes with us to learn:   • Key questions to ask when considering a partnership to accelerate your business into the cloud • Pitfalls and mistakes other partners…

839 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question