Solved

Neovo Monitor Problem

Posted on 2006-06-14
6
1,269 Views
Last Modified: 2012-05-05
Hello
I own a neovo E-19A monitor , today when I was reading an article on the monitor , suddenly the light of screen decreased and after 2 seconds screen blanked ! when I turn it off and on , the screen comes with low light and then after 2 seconds goes blank again. I was using the dvi cable , I cahnged with a analog vga cable. no difference. when monitor is on the led is green and no error message is on the screen , I saw some other people have had the same problem in other forums, but couldnt find any solution. any help is appreciated
0
Comment
Question by:fifthelement80
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 3
  • 3
6 Comments
 
LVL 69

Accepted Solution

by:
Callandor earned 500 total points
ID: 16904764
If you can still see a faint outline of what is on the display, then I think the inverter is broken, which can be replaced.
0
 
LVL 7

Author Comment

by:fifthelement80
ID: 16905031
yes I can see a faint outline on the screen , is there any way I can test the inverter ? to be sure inverter is broken ?
0
 
LVL 69

Expert Comment

by:Callandor
ID: 16905147
I don't replace these units, so I can't tell you what to test.  Either the backlight or the inverter are the cause of these problems, and the fact that the light shows briefly tells me the bulb is ok.  By process of elimination, that leaves the inverter.  If you swap another unit in and the problem disappears, that would be confirmation.
0
Salesforce Has Never Been Easier

Improve and reinforce salesforce training & adoption using WalkMe's digital adoption platform. Start saving on costly employee training by creating fast intuitive Walk-Thrus for Salesforce. Claim your Free Account Now

 
LVL 7

Author Comment

by:fifthelement80
ID: 16905186
thx callandor for you reply , do u have any guide or tutorial showing how to do it ?
0
 
LVL 69

Expert Comment

by:Callandor
ID: 16905346
You have to be very careful with the cold cathode tubes.  The inverter powers the tubes.
http://www.inventgeek.com/Projects/shorts/overview.aspx
0
 
LVL 7

Author Comment

by:fifthelement80
ID: 16999519
Thx Callandor , I still had no success repairing it , because neovo doesnt offer customer service in my country , but u were right about inverter problem , so u get the points.
Regards
0

Featured Post

Enterprise Mobility and BYOD For Dummies

Like “For Dummies” books, you can read this in whatever order you choose and learn about mobility and BYOD; and how to put a competitive mobile infrastructure in place. Developed for SMBs and large enterprises alike, you will find helpful use cases, planning, and implementation.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

This paper addresses the security of Sennheiser DECT Contact Center and Office (CC&O) headsets. It describes the DECT security chain comprised of “Pairing”, “Per Call Authentication” and “Encryption”, which are all part of the standard DECT protocol.
A clone is a duplicate copy. Sheep have been cloned and maybe someday even people will be cloned, but disk cloning (performed by the hard drive cloning software) is a vital tool used to manage and protect data. Let’s look at what hard drive cloning …
The Email Laundry PDF encryption service allows companies to send confidential encrypted  emails to anybody. The PDF document can also contain attachments that are embedded in the encrypted PDF. The password is randomly generated by The Email Laundr…

738 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question