Want to win a PS4? Go Premium and enter to win our High-Tech Treats giveaway. Enter to Win

x
?
Solved

VPN connection between Pix 506e and Symantec vpn 100 troubles

Posted on 2006-06-20
3
Medium Priority
?
413 Views
Last Modified: 2013-11-16
I currently have a VPN between a Linksys and a Symantec vpn 100.  I am trading the linksys with a Pix 506e.  I have tried to configure everything according to the linksys, but am still not getting any results.
0
Comment
Question by:tashmore
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
3 Comments
 

Author Comment

by:tashmore
ID: 16948527
I am using gui's for both firewalls.  I'm not sure how to start troubleshooting or what to look for.
0
 

Author Comment

by:tashmore
ID: 16948631
These are the configurations from my symantec router

IPSEC
      Security Assocation      Main-oFFICe
      PPPoE session      Session1
      phase negotiation      main mode
      encryption            esp 3des
      authentication      md5
      SA Lifetime      480 minutes
      Data volume limit      0 Kb
      Inactivity timeout      0 minutes
      Perfect Forward Secr..Enable
Local Security Gateway
      IP Address
Remote Security Gateway
      Remote office IP
      Pre-shared Key            
Gateway-to-Gateway Tunnels
      NetBIOS Broadcast      enable
      Global Tunnel      disable
      remote subnet IP      192.168.2.0      255.255.255.0
      MTU       LAN PC 1500              WAN port 1500
      Echo Request timeout 20 sec      Retry 5
      Allow IDENT Port      disable
      NAT function       enable
      RIP V2            Disable
      IPSEC type            2spI

T
0
 
LVL 19

Accepted Solution

by:
nodisco earned 500 total points
ID: 16949600
Hi there

Have a look at this URL for step by step instructions on how to do this:

http://service1.symantec.com/SUPPORT/ent-gate.nsf/0/70696f0e28bd63a280256eeb003aef23?OpenDocument&seg=hm

When configured - to check what is happening on the PIX regarding debugging:

conf t
debug crypto isakmp
logging console 7
logging on

This will output isakmp negotiations and will show where its going astray.  It looks a bit crazy but if you post the output, we should be able to assist
0

Featured Post

Threat Trends for MSPs to Watch

See the findings.
Despite its humble beginnings, phishing has come a long way since those first crudely constructed emails. Today, phishing sites can appear and disappear in the length of a coffee break, and it takes more than a little know-how to keep your clients secure.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

WARNING:   If you follow the instructions here, you will wipe out your VTP and VLAN configurations.  Make sure you have backed up your switch!!! I recently had some issues with a few low-end Cisco routers (RV325) and I opened a case with Cisco TA…
There’s a movement in Information Technology (IT), and while it’s hard to define, it is gaining momentum. Some call it “stream-lined IT;” others call it “thin-model IT.”
Both in life and business – not all partnerships are created equal. As the demand for cloud services increases, so do the number of self-proclaimed cloud partners. Asking the right questions up front in the partnership, will enable both parties …
Both in life and business – not all partnerships are created equal. Spend 30 short minutes with us to learn:   • Key questions to ask when considering a partnership to accelerate your business into the cloud • Pitfalls and mistakes other partners…
Suggested Courses

609 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question