Solved

Policy Map on Subinterface

Posted on 2006-06-27
12
552 Views
Last Modified: 2012-06-27
I have several locations in my network.  Some have Cisco 2800's with 2 physical ethernet interfaces - these are ok.  The issue is with a 2600 at one site that has only one physical enet interface.  I am trying to put a policy map using the following commands to force traffic from a specific IP to the video plane on my ISP's mpls network:

ip cef

!

!

ip access-list extended video

  permit ip host 172.16.102.11 any

!

!

class-map match-all video

  match access-group name video

!

!

policy-map outbound

   class video

   set ip precedence 4

   bandwidth 845

   class class-default

   set ip precedence 0

!

!

!

interface fa0/1.76

 service-policy output outbound

The issue appears to be that policy maps are not supported on subinterfaces - is there any way I can still accomplish this goal with the existing hardware?  Would it work to put the map on the main interface?

0
Comment
Question by:mrsmileyns
  • 6
  • 6
12 Comments
 
LVL 12

Expert Comment

by:Scotty_cisco
Comment Utility
what version of code are you running?

Thanks
Scott
0
 

Author Comment

by:mrsmileyns
Comment Utility
IOS 12.3(12D)
0
 
LVL 12

Expert Comment

by:Scotty_cisco
Comment Utility
actually looking to see if it was a plus feature set what is the image name?
0
 

Author Comment

by:mrsmileyns
Comment Utility
"flash:c2600-advipservicesk9-mz.123-12d.bin
0
 
LVL 12

Expert Comment

by:Scotty_cisco
Comment Utility
you could put this in the main interface it would apply to all traffic that was defined in the ACL one problem I do see is that you are trying to apply this outbound and you can not do that inbound is the only way a route map works you could put it in your serial or outside facing interface.

Thanks
Scott
0
 

Author Comment

by:mrsmileyns
Comment Utility
actually, this ethernet sub interface is the outbound interface facing the ISP's bridge - there is no serial connection to the ISP
0
How your wiki can always stay up-to-date

Quip doubles as a “living” wiki and a project management tool that evolves with your organization. As you finish projects in Quip, the work remains, easily accessible to all team members, new and old.
- Increase transparency
- Onboard new hires faster
- Access from mobile/offline

 
LVL 12

Expert Comment

by:Scotty_cisco
Comment Utility
then just turn the map around and put it on the subinterface facing your lan.
0
 

Author Comment

by:mrsmileyns
Comment Utility
interface 0/1.76 points to the ISP''s private MPLS network, and interface 0/1 points to the LAN
0
 
LVL 12

Accepted Solution

by:
Scotty_cisco earned 500 total points
Comment Utility
then you would want to put it in the fa 0/1 interface not the subinterface and then you may want to expand your ACL so it only tags Video traffic rather than everything from that host.

Thanks
Scott
0
 

Author Comment

by:mrsmileyns
Comment Utility
alrighty - sounds good - thanks for your help.
0
 

Author Comment

by:mrsmileyns
Comment Utility
it worked - my ISP is seeing the traffic correctly in the video plane - thanks :)
0
 
LVL 12

Expert Comment

by:Scotty_cisco
Comment Utility
:) glad to hear it .... unfortunately I have a little more experiance on this than I want to admit... worked for a Satellite provider for 5 years everything was QoS'ed as it were.

Thanks
Scott
0

Featured Post

IT, Stop Being Called Into Every Meeting

Highfive is so simple that setting up every meeting room takes just minutes and every employee will be able to start or join a call from any room with ease. Never be called into a meeting just to get it started again. This is how video conferencing should work!

Join & Write a Comment

Suggested Solutions

This article is a guide to configure bridging on Cisco Routers.  This is something I never knew was possible until after making a few phone calls to Cisco.  Using bridging saved our company money by not requiring us to purchase a new switch.  Bridgi…
Quality of Service (QoS) options are nearly endless when it comes to networks today. This article is merely one example of how it can be handled in a hub-n-spoke design using a 3-tier configuration.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

763 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

11 Experts available now in Live!

Get 1:1 Help Now