Solved

how to allow trafic from router to router within IP Table Unix firewall

Posted on 2006-07-12
3
436 Views
Last Modified: 2013-11-29
Hi,

Router1's configuration
------------------------------------------------------------
interface eth 0/1
  ip address  192.168.100. 254 255.255.255.0
  no shutdown
!
interface t1 1/1
  tdm-group 1 timeslots 1-24 speed 64
  no shutdown
!
interface ppp 1
  ip address  10.10.10.1  255.255.255.0
  no shutdown
  cross-connect 1 t1 1/1 1 ppp 1
!
ip route 0.0.0.0 0.0.0.0 10.10.10.2
ip route 192.168.99.0 255.255.255.0 10.10.10.2
------------------------------------------------------------

Router2's configuration
------------------------------------------------------------
interface eth 0/1
  ip address  192.168.99.1  255.255.255.0
  no shutdown
!
interface t1 1/1
  tdm-group 1 timeslots 1-24 speed 64
  no shutdown
!
interface ppp 1
  ip address  10.10.10.2  255.255.255.0
  no shutdown
  cross-connect 1 t1 1/1 1 ppp 1
!
ip route 0.0.0.0 0.0.0.0 10.10.10.1
ip route 192.168.100.0 255.255.255.0 10.10.10.1
------------------------------------------------------------

Sernerio:
Router1 are known to be within an IP Table Proxy firewall ( www.netfilter.org ) hosting on UNIX with a gateway 192.168.100.1
within the Router1 router, i was able to ping router2 network, including both gateway and the host addresses

from router2 location, within the router, i was able to ping router1 gateway
ex; 192.168.100.254 , and 10.10.10.1 but i cannot ping 192.168.100.1 and the host adresses

Withing the Router1 location, from the router1, i can ping 192.168.100.1 and the host addresses

so i suppose IP Table has block trafic for router2 to access router1 location!

what are the appropreate way to configure the IP Table to allow trafic from router2?

Thanks
0
Comment
Question by:techguy07
  • 2
3 Comments
 
LVL 2

Expert Comment

by:Todd_Bunch
ID: 17091802
0
 

Author Comment

by:techguy07
ID: 17093579
my Senior Manager forward to ethernet port, and it works.

Thanks, How can i close this thread?
0
 
LVL 2

Accepted Solution

by:
Todd_Bunch earned 500 total points
ID: 17093822
Just accept the answer from someone or ask a moderator to close it for you.
0

Featured Post

Netscaler Common Configuration How To guides

If you use NetScaler you will want to see these guides. The NetScaler How To Guides show administrators how to get NetScaler up and configured by providing instructions for common scenarios and some not so common ones.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Even if you have implemented a Mobile Device Management solution company wide, it is a good idea to make sure you are taking into account all of the major risks to your electronic protected health information (ePHI).
If you're not part of the solution, you're part of the problem.   Tips on how to secure IoT devices, even the dumbest ones, so they can't be used as part of a DDoS botnet.  Use PRTG Network Monitor as one of the building blocks, to detect unusual…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Get a first impression of how PRTG looks and learn how it works.   This video is a short introduction to PRTG, as an initial overview or as a quick start for new PRTG users.

911 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

20 Experts available now in Live!

Get 1:1 Help Now