?
Solved

Entity alarms on cisco 7200

Posted on 2006-07-13
6
Medium Priority
?
3,966 Views
Last Modified: 2008-01-09
Hi can any one help with these,

I get the below alarms for the se1/0, constantly, the carriers has checked out the link and cannot find anything
Does anyone know what these mean ? is this ios  related ?


Jul 13 05:22:45: %ENTITY_ALARM-6-INFO: ASSERT MAJOR Se1/0 Receiver has remote alarm
Jul 13 05:22:46: %ENTITY_ALARM-6-INFO: CLEAR MAJOR Se1/0 Receiver has remote alarm
Jul 13 06:54:57: %ENTITY_ALARM-6-INFO: ASSERT MAJOR Se1/0 Receiver has remote alarm
Jul 13 06:54:58: %ENTITY_ALARM-6-INFO: CLEAR MAJOR Se1/0 Receiver has remote alarm
Jul 13 07:44:09: %ENTITY_ALARM-6-INFO: ASSERT MAJOR Se1/0 Receiver has remote alarm
Jul 13 07:44:10: %ENTITY_ALARM-6-INFO: CLEAR MAJOR Se1/0 Receiver has remote alarm
Jul 13 07:55:26: %ENTITY_ALARM-6-INFO: ASSERT MAJOR Se1/0 Receiver has remote alarm
Jul 13 07:55:27: %ENTITY_ALARM-6-INFO: CLEAR MAJOR Se1/0 Receiver has remote alarm
Jul 13 08:25:32: %ENTITY_ALARM-6-INFO: ASSERT MAJOR Se1/0 Receiver has remote alarm
Jul 13 08:25:33: %ENTITY_ALARM-6-INFO: CLEAR MAJOR Se1/0 Receiver has remote alarm

interface Serial1/0
  bandwidth 10000
 no ip address
 encapsulation frame-relay IETF
 load-interval 30
 framing g751
 dsu bandwidth 34010
 serial restart-delay 0
 traffic-shape rate 10000000 10000000 0 1000
 frame-relay lmi-type ansi
 frame-relay intf-type dce
!
interface Serial1/0.1 point-to-point

 ip address 10.0.10.234 255.255.255.252
 frame-relay interface-dlci 100
!
interface Serial1/0.2 point-to-point
 
 ip vrf forwarding NUG_RAC_Spoke_VRF1
 ip address 10.0.10.126 255.255.255.252
 ip nat outside
 ip virtual-reassembly
 frame-relay interface-dlci 200
!

Serial1/0 is up, line protocol is up
  Hardware is M1T-E3 pa
  Description: IPVPN WAN link via C&W Q22274A
  MTU 4470 bytes, BW 10000 Kbit, DLY 200 usec,
     reliability 255/255, txload 30/255, rxload 54/255
  Encapsulation FRAME-RELAY IETF, crc 16, loopback not set
  Keepalive set (10 sec)
  Restart-Delay is 0 secs
  LMI enq sent  0, LMI stat recvd 0, LMI upd recvd 0
  LMI enq recvd 1398330, LMI stat sent  1398330, LMI upd sent  0, DCE LMI up
  LMI DLCI 0  LMI type is ANSI Annex D  frame relay DCE
  Broadcast queue 0/256, broadcasts sent/dropped 466129/0, interface broadcasts 0
  Last input 00:00:00, output 00:00:00, output hang never
  Last clearing of "show interface" counters 23w0d
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 1959932
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  30 second input rate 2122000 bits/sec, 588 packets/sec
  30 second output rate 1213000 bits/sec, 787 packets/sec
     471049592 packets input, 2491861272 bytes, 0 no buffer
     Received 0 broadcasts, 63 runts, 0 giants, 0 throttles
              0 parity
     2851 input errors, 2471 CRC, 0 frame, 360 overrun, 0 ignored, 20 abort
     2500538258 packets output, 1460165684 bytes, 26 underruns
     0 output errors, 0 applique, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
     18188 carrier transitions
   rxLOS inactive, rxLOF inactive, rxAIS inactive
   txAIS inactive, rxRAI inactive, txRAI inactive


AR1415#sh ver
Cisco IOS Software, 7200 Software (C7200-IS-M), Version 12.3(14)T3, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 12-Jul-05 01:47 by ccai

ROM: System Bootstrap, Version 12.2(4r)B2, RELEASE SOFTWARE (fc2)
BOOTLDR: 7200 Software (C7200-KBOOT-M), Version 12.2(15)T8,  RELEASE SOFTWARE (fc2)

AR1415 uptime is 25 weeks, 2 days, 14 hours, 37 minutes
System returned to ROM by power-on
System restarted at 18:26:40 UTC Mon Jan 16 2006
System image file is "disk0:c7200-is-mz.123-14.T3.bin"

Cisco 7204VXR (NPE400) processor (revision B) with 229376K/32768K bytes of memory.
Processor board ID 33559079
R7000 CPU at 350MHz, Implementation 39, Rev 3.3, 256KB L2 Cache
4 slot VXR midplane, Version 2.11

Last reset from power-on

PCI bus mb0_mb1 (Slots 0, 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb0_mb1 has a total of 490 bandwidth points.
This configuration is within the PCI bus capacity and is supported.

PCI bus mb2 (Slots 2, 4, 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points
This configuration is within the PCI bus capacity and is supported.

Please refer to the following document "Cisco 7200 Series Port
Adaptor Hardware Configuration Guidelines" on CCO <www.cisco.com>,
for c7200 bandwidth points oversubscription/usage guidelines.


2 FastEthernet interfaces
1 Serial interface
125K bytes of NVRAM.

125952K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
8192K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102
0
Comment
Question by:biswar
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
  • 2
6 Comments
 
LVL 12

Expert Comment

by:Scotty_cisco
ID: 17104218
this is from Cisco's website

ENTITY_ALARM Messages

The following are entity alarm messages.

Error Message    

%ENTITY_ALARM-6-INFO : [chars] [chars] [chars] [chars] [chars]

Explanation    Alarm assertion or deassertion information.

Recommended Action    No action is required.

I would say not a problem no action is required ...... they are just informational alarms

Thanks
Scott
0
 

Author Comment

by:biswar
ID: 17110269
the problem i have is these drops as below, every so often pcs

Last clearing of "show interface" counters 23w0d
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 1959932
 2851 input errors, 2471 CRC, 0 frame, 360 overrun, 0 ignored, 20 abort

the reason for the output drops i belive is that, the serial interface cannot send data out, so the buffer gets full up and then eventually drops them
and the other errors


thanks


0
 
LVL 12

Expert Comment

by:Scotty_cisco
ID: 17456214
The question was answered .... they are informational alerts and do not require anything to be done.

Thanks
scott
0
 

Author Comment

by:biswar
ID: 17461876
yes can be closed, raised a tac case and they advisec a ios upgrade, which was done and the errors have disappeared
0
 
LVL 1

Accepted Solution

by:
DarthMod earned 0 total points
ID: 17470279
PAQed with points refunded (500)

DarthMod
Community Support Moderator
0

Featured Post

Supports up to 4K resolution!

The VS192 2-Port 4K DisplayPort Splitter is perfect for anyone who needs to send one source of DisplayPort high definition video to two or four DisplayPort displays. The VS192 can split and also expand DisplayPort audio/video signal on two or four DisplayPort monitors.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

In this tutorial I will show you with short command examples how to obtain a packet footprint of all traffic flowing thru your Juniper device running ScreenOS. I do not know the exact firmware requirement, but I think the fprofile command is availab…
New Server 172.16.200.2  was moved from behind Router R2 f0/1 to behind router R1 int f/01 and has now address 172.16.100.2. But we want users still to be able to connected to it by old IP. How to do it ? We can used destination NAT (DNAT).  In DNAT…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses

762 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question