Solved

Cisco 1605

Posted on 2006-10-23
5
272 Views
Last Modified: 2010-04-17
Hi,

I've just inherited the management of a cisco 1605 & i need a bit of help. I was wondering how i can view the free space on it because i think the config might be to big. I was also wondering how to do IP groups. I know how to do it on a PIX but this seems different.

Thanks
0
Comment
Question by:inf2300
  • 3
  • 2
5 Comments
 
LVL 50

Expert Comment

by:Don Johnston
ID: 17788772
Do a "show start". Near the top will be a line that says something like "1250 bytes used". This tells you how much NVRAM you are using.

Then do a "show version". Near the bottom will be a line that says something like "16364 bytes of Non-volitile memory." This tells you how much total NVRAM is installed. The difference is how much is available.

0
 

Author Comment

by:inf2300
ID: 17790077
Thanks for the response,

show start
        Using 2563 out of 7506 bytes, uncompressed size = 11380 bytes

show version
cisco 1605 (68360) processor (revision C) with 7680K/512K bytes of memory.
Processor board ID 12850384, with hardware revision 00000000 Bridging software.
2 Ethernet/IEEE 802.3 interface(s)
System/IO memory with parity disabled
8192K bytes of DRAM onboard
System running from RAM
8K bytes of non-volatile configuration memory.
2048K bytes of processor board PCMCIA flash (Read/Write)

So i take it i have room left if i'm using 2563 out of 7506
0
 
LVL 50

Expert Comment

by:Don Johnston
ID: 17791128
I had forgotten that "show start" displays total NVRAM also.

Yes, you have room left. About 5K.
0
 

Author Comment

by:inf2300
ID: 17791458
Thanks!!!

Last thing... I think i could shrink my configuration considerably by using groups. Can i do it using Version 11.2

example

access-list 103 permit ip XXX.XXX.XXX.XXX 0.0.0.255 host IP1
access-list 103 permit ip XXX.XXX.XXX.XXX 0.0.0.255 host IP2
access-list 103 permit ip XXX.XXX.XXX.XXX 0.0.0.255 host IP3
access-list 103 permit ip XXX.XXX.XXX.XXX 0.0.0.255 host IP4

It's always the same but for different XXX.XXX.XXX.XXX and it's always the same IP1 to 4.

How would i go about grouping them?

Thanks
0
 
LVL 50

Accepted Solution

by:
Don Johnston earned 500 total points
ID: 17791489
I think you need to start another question for that...
0

Featured Post

Simple, centralized multimedia control

Watch and learn to see how ATEN provided an easy and effective way for three jointly-owned pubs to control the 60 televisions located across their three venues utilizing the ATEN Control System, Modular Matrix Switch and HDBaseT extenders.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Problem to router 7 82
Cisco 3560 Switch with Multiple Gateways 10 80
I can't ping a loopback IP on one router from another router in GNS3 5 28
Access-List 15 29
Problem Description:   Couple of months ago we upgraded the ADSL line at our branch office from Home to Business line. The purpose of transforming the service to have static public IP’s. We were in need for public IP’s to publish our web resour…
In the world of WAN, QoS is a pretty important topic for most, if not all, networks. Some WAN technologies have QoS mechanisms built in, but others, such as some L2 WAN's, don't have QoS control in the provider cloud.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

756 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question