Solved

Removing vlan from a Catalyst 2940

Posted on 2006-10-24
4
421 Views
Last Modified: 2008-03-04
I'm trying to remove some of the vlans from our Catalyst 2940


VLAN Name                             Status    Ports                                                    
---- -------------------------------- --------- -------------------------------                                                                              
1    default                               active    Fa0/1, Fa0/2, Fa0/3, F                                                                    
                                                           Fa0/5, Fa0/6, Fa0/7, Fa0/8                                                                          
                                                           Gi0/1
                                                     
100  AVVID                              active    Fa0/1, Fa0/2, Fa0/3, Fa0/4                                                                          
                                                           Fa0/5, Fa0/6, Fa0/7, Fa0/8                                                                          
416  EAST2-Closet                    active                                            
420  BH-9777                           active                                            
950  Development                     active                                            
1000 IT_NETWORK                   active                                            
1002 fddi-default                      act/unsup                                              
1003 token-ring-default             act/unsup                                              
1004 fddinet-default                 act/unsup                                              
1005 trnet-default                    act/unsup


I'm trying to remove them by typing "no vlan 416", but I'm getting the following error:  % Invalid input detected at '^' marker.
I need to remove at the very least vland 416, 420, 950.

Thanks
Tom
0
Comment
Question by:martit01
  • 2
  • 2
4 Comments
 
LVL 79

Accepted Solution

by:
lrmoore earned 500 total points
ID: 17799581
switch#vlan data
switch(vlan)#no vlan 416
switch(vlan)#exit
Apply completed
Exiting...
switch#
0
 

Author Comment

by:martit01
ID: 17800777
Worked perfectly, thanks Irmoore.....    so now the vlan 1 name is "Default", can you tell me how to change the name?

Thanks
0
 
LVL 79

Expert Comment

by:lrmoore
ID: 17802627
I don't think you can change anything on vlan1 it is always "default"
If you could, the procedure would be:

switch#vlan data
switch(vlan)#vlan 1 name MyVLAN1
switch(vlan)#exit
Apply completed
Exiting...
switch#sho vlan

0
 

Author Comment

by:martit01
ID: 17807711
it doesn't seem to allow me to change the "default" name.  Thanks for your help.
0

Featured Post

PRTG Network Monitor: Intuitive Network Monitoring

Network Monitoring is essential to ensure that computer systems and network devices are running. Use PRTG to monitor LANs, servers, websites, applications and devices, bandwidth, virtual environments, remote systems, IoT, and many more. PRTG is easy to set up & use.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Cisco Sup720 Migrate to Sup2T 5 69
BGP Code 12 47
Port Forwarding on Cisco 881 14 57
2 routers and 1 public IP Address. 10 41
It happens many times that access list (ACL) have to be applied to outgoing router interface in order to limit some traffic.This article is about how to test ACL from the router which is not very intuitive for everyone. Below scenario shows simple s…
Quality of Service (QoS) options are nearly endless when it comes to networks today. This article is merely one example of how it can be handled in a hub-n-spoke design using a 3-tier configuration.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

777 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question