Solved

Connect wireless connection to Class B network

Posted on 2006-10-30
3
241 Views
Last Modified: 2010-03-19
We previously had a class C network.  Were running out of IP's.

Now have a class B network, with Cisco 5510 connected to DSL and Cisco 50x connected to cable.  DHCP provided by netware server.  Previously, with Class C address, we had a Linksys wireless access point connected to the network to provide internet access for outside board of directors.

We currently have available Linksys router from old Class C network that connected to cable modem.

DSL - Cisco 5510 - 172.16.0.1, 255.255.0.0  Iprism network access device protects this device
Cable - Cisco 50x - 172.16.1.3 255.255.0.0

We would like to use the Linksys wireless access point to connect to the linkysys router to go over the 172.16.1.3 gateway.  It would be ideal to have DHCP provided by the Linksys router only to wireless users using Class C Address and go directly to the 172.16.1.3 gateway without access to any of the Class B network addresses other than the 172.16.1.3 gateway.  Is this possible and how do you configure the Linksys router.

I was not using the Wan port and tried to configure an older Linksys router, setting in router versus gateway mode and could not get it to work properly.

Thanks.

Cliff
0
Comment
Question by:cwsoft05
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
3 Comments
 
LVL 9

Accepted Solution

by:
jasonr0025 earned 250 total points
ID: 17839515
I have a similar situation except I have 1 boadband line and 6 ip address
I have one Ip address on pix 506e for primary network and one ip on 3com router for pc lab.
I added buffalo wireless router to 3com for public wirelss ap but I too wanted it on seperate network.
Run cable from lan port on router to wan on linksys
Set linksys router to dhcp on wan interface or you can add static ip on wan inside the 172.16.1 network.
Set linksys as dhcp router to lan clients and use default 192.168.1.x range.

Wireless encryption, ssid and such is up to you but this should take care of what you need.
0
 

Author Comment

by:cwsoft05
ID: 17842265
0
 
LVL 9

Expert Comment

by:jasonr0025
ID: 17842509
Thanks and I am glad you got it going
0

Featured Post

Independent Software Vendors: We Want Your Opinion

We value your feedback.

Take our survey and automatically be enter to win anyone of the following:
Yeti Cooler, Amazon eGift Card, and Movie eGift Card!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Internet options/Settings 1 68
can't ssh to external IP 9 63
Adnexus.net keeps getting hit from OpenDNS 12 61
SSL-VPN 1 50
Join Greg Farro and Ethan Banks from Packet Pushers (http://packetpushers.net/podcast/podcasts/pq-show-93-smart-network-monitoring-paessler-sponsored/) and Greg Ross from Paessler (https://www.paessler.com/prtg) for a discussion about smart network …
Most of the applications these days are on Cloud. Cloud is ubiquitous with many service providers in the market. Since it has many benefits such as cost reduction, software updates, remote access, disaster recovery and much more.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Get a first impression of how PRTG looks and learn how it works.   This video is a short introduction to PRTG, as an initial overview or as a quick start for new PRTG users.

749 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question