Solved

Application Error Message - MSExchangeTransport

Posted on 2006-11-28
5
296 Views
Last Modified: 2006-11-28
Hello,

Any ideas about what this error message means:

Event Type:      Error
Event Source:      MSExchangeTransport
Event Category:      NDR
Event ID:      3008
Date:            11/28/2006
Time:            3:50:51 PM
User:            N/A
Computer:      ROLLINS
Description:
A non-delivery report with a status code of 5.0.0 was generated for recipient rfc822;someone@email.com (Message-ID <2FDD167180D6644DA6EC40900F2F995101326ACA@rollins.ForcedExposure.local>).  
Cause:  This indicates a permanent failure. Possible causes :  1)No route is defined for a given address space. For example, an SMTP connector is configured, but this recipient address does not match the address spaces for which it routes mail.  2)Domain Name Server (DNS) returned an authoritative host not found for the domain.  3)The routing group does not have a connector defined û mail from one server in the routing group has no way to get to another routing group.    
Solution: Verify that this error is not caused by a DNS lookup problem, and then check the address spaces configured on your STMP connectors. If you are delivering Internet mail through an SMTP connector,  consider adding an address space of type SMTP with value ô*ö (an asterisk) to one of the SMTP connectors to make routing possible. Verify all routing groups are connected to each other through a routing group connector or another connector.

For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.


Thanks, Kristin
0
Comment
Question by:forcedexposure
  • 3
  • 2
5 Comments
 
LVL 39

Accepted Solution

by:
redseatechnologies earned 250 total points
ID: 18033071
Hi forcedexposure,

Is someone@email.com a legitimate address?

If so, can you put both your domain and their domain into http://www.dnsreport.com - fix any problems you have, and then try it again

If it is not a legitimate address (someone you are not trying to email) then you should look at some form of recipient filtering

Hope that helps,

-red
0
 

Author Comment

by:forcedexposure
ID: 18033097
Hi Red,

That email address is bogus - I didn't want to leave a contact's email address on Experts-Exchange.

I'll try what you've suggested above and get back to you.

Thanks! Kristin
0
 
LVL 39

Expert Comment

by:redseatechnologies
ID: 18033115
>>That email address is bogus

I figured that you munged it, what I wanted to know is if it was a legitimate email address you were actually trying to email, or if it was something you have never seen before.

I assume it is legitimate, in which case, check out their and your domain (I can see one problem already, but we will see what DNS report says)

-red
0
 

Author Comment

by:forcedexposure
ID: 18033513
Hi Red,

Thanks for the advice. I've bookmarked that DNSreports.com page.
Turns out that our collegue is having problems with his mail server.

& I was concerned because we were having problems with our mailserver recently.

Thanks again for your help!!

Best, Kristin
0
 
LVL 39

Expert Comment

by:redseatechnologies
ID: 18033534
Glad to hear you got it sorted.

Thanks

-red
0

Featured Post

Optimizing Cloud Backup for Low Bandwidth

With cloud storage prices going down a growing number of SMBs start to use it for backup storage. Unfortunately, business data volume rarely fits the average Internet speed. This article provides an overview of main Internet speed challenges and reveals backup best practices.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Disabling the Directory Sync Service Account in Office 365 will stop directory synchronization from working.
Local Continuous Replication is a cost effective and quick way of backing up Exchange server data. The following article describes the steps required to configure Local Continuous Replication. Also, the article tells you how to restore from a backup…
To show how to generate a certificate request in Exchange 2013. We show this process by using the Exchange Admin Center. Log into Exchange Admin Center.:  First we need to log into the Exchange Admin Center. Navigate to the Servers >> Certificates…
A short tutorial showing how to set up an email signature in Outlook on the Web (previously known as OWA). For free email signatures designs, visit https://www.mail-signatures.com/articles/signature-templates/?sts=6651 If you want to manage em…

785 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question