Want to win a PS4? Go Premium and enter to win our High-Tech Treats giveaway. Enter to Win


pix 506e config and exchange 2003

Posted on 2006-11-29
Medium Priority
Last Modified: 2013-11-16
I need to allow smtp to come in to the exchange 2003 server through the pix 506e. I am also going to allow port 443 in for OWA. Can you tell me what i need in this config? Also, about 3/4 of the way down on the config, i have an   !incomplete   line. I can't figure out what this is from. Thanks in advance

fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
name fs1.fvr.local
access-list inside_outbound_nat0_acl permit ip any
access-list outside_cryptomap_dyn_20 permit ip any
access-list internal permit ip
access-list outside_access_in permit tcp any host  eq 3390
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside
ip address inside
ip audit info action alarm
ip audit attack action alarm
ip local pool vpnpool
pdm location inside
pdm location inside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_outbound_nat0_acl
nat (inside) 1 0 0
static (inside,outside) tcp  3390 fs1.fvr.local 3389 netmask 0 0
access-group outside_access_in in interface outside
route outside  1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto map mymap 10 ipsec-isakmp
! Incomplete
isakmp enable outside
isakmp nat-traversal 20
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption 3des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
vpngroup address-pool vpnpool
vpngroup dns-server
vpngroup default-domain
vpngroup idle-time 1800
vpngroup password
telnet inside
telnet timeout 5
ssh outside
ssh timeout 30
console timeout 0
vpdn enable outside
dhcpd address inside
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
username password encrypted privilege 15
terminal width 80
: end

Question by:fina27
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 3
  • 2
LVL 11

Accepted Solution

prueconsulting earned 2000 total points
ID: 18042817
The incomplete line is due to a an incomplete crypto map for VPN.

crypto map mymap 10 ipsec-isakmp
! Incomplete

For exchange do no fixup smtp 25

the fixup smtp 25 will break exchange

access-list outside_access_in permit tcp any host  eq 3390
access-list outside_access_in permit tcp any <interface ip> eq 25 <-- This will allow email traffic to hit the interface and be accepted.
access-list outside_access+in permit tcp any <interface ip> eq 443

static (inside,outside) tcp external 25 internal 25 netmask 0 0


Author Comment

ID: 18042837
and then the access group right?
LVL 11

Expert Comment

ID: 18042877
the access group is already applied
 but yes

access-group outside-access_in in interface outside

Author Comment

ID: 18073942
why do i have to write the "access-list outside_access_in permit tcp any host  eq 3390" first? isn't that irrelevant?
LVL 11

Expert Comment

ID: 18074176
sometimes the acl gets removed when you make changes. worse case it will tell you its a duplicate line

Featured Post

When ransomware hits your clients, what do you do?

MSPs: Endpoint security isn’t enough to prevent ransomware.
As the impact and severity of crypto ransomware attacks has grown, Webroot fought back, not just by building a next-gen endpoint solution capable of preventing ransomware attacks but also by being a thought leader.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

This past year has been one of great growth and performance for OnPage. We have added many features and integrations to the product, making 2016 an awesome year. We see these steps forward as the basis for future growth.
Considering cloud tradeoffs and determining the right mix for your organization.
As a trusted technology advisor to your customers you are likely getting the daily question of, ‘should I put this in the cloud?’ As customer demands for cloud services increases, companies will see a shift from traditional buying patterns to new…
Both in life and business – not all partnerships are created equal. Spend 30 short minutes with us to learn:   • Key questions to ask when considering a partnership to accelerate your business into the cloud • Pitfalls and mistakes other partners…
Suggested Courses

609 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question