EventID Errors: 1010, 1014, 1016 DHCPServer

genesissi
genesissi used Ask the Experts™
on
I have been receiving the following errors:

Event Type:      Error
Event Source:      DhcpServer
Event Category:      None
Event ID:      1010
Date:            1/3/2007
Time:            1:18:12 PM
User:            N/A
Computer:SERVER1
Description:
The DHCP service encountered the following error while cleaning  up the database:
An error occurred while accessing the DHCP database. Look at the
DHCP server event log for more information on this error.

Event Type:      Error
Event Source:      DhcpServer
Event Category:      None
Event ID:      1014
Date:            1/3/2007
Time:            1:18:12 PM
User:            N/A
Computer:      SERVER1
Description:
 The following problem occurred with the Jet database -1032:  Jet database read or write operations failed. If the computer  or database has just been upgraded, then this message can be  safely ignored. If this message appears frequently, either there  is not enough disk space to complete the operation or the database  or backup database may be corrupt.  To correct this problem,  either free additional space on your hard disk or restore the  database. After you restore the database, ensure that conflict  detection is enabled in DHCP server properties. For information  about restoring the database, see Help and Support Center.  Additional Debug Information: JetBackup.

Event Type:      Error
Event Source:      DhcpServer
Event Category:      None
Event ID:      1016
Date:            1/3/2007
Time:            1:18:12 PM
User:            N/A
Computer:      SERVER1
Description:
The DHCP service encountered the following error when  backing up the database:
An error occurred while accessing the DHCP database. Look at the
DHCP server event log for more information on this error.

Has anyone encountered this as well?  Found a solution or some good resources?
Thanks.
Comment
Watch Question

Do more with

Expert Office
EXPERT OFFICE® is a registered trademark of EXPERTS EXCHANGE®
There are a few possibilities for this,

Do you have any AV software installed on this server?
Do you have indexing enabled on the server? (Right click on C:\ > properties > general > allowing indexing.....)

-red
Jeffrey Kane - TechSoEasyPrincipal Consultant
Most Valuable Expert 2016
Top Expert 2014

Commented:
This list of events as well as the others that you posted are indicitive of having ISA2004 installed without the latest service pack.

Please be sure that you have updated to Service Pack 1 and/or have disabled the RPC Filter in ISA.

http://support.microsoft.com/kb/887222

Jeff
TechSoEasy

Author

Commented:
No ISA 2004 installed.
JavaScript Best Practices

Save hours in development time and avoid common mistakes by learning the best practices to use for JavaScript.

Author

Commented:
Thanks for the responses and sorry for the delay, found out I was building a server with SAP when it arrived.
And I have no experience with SAP :)

I have Symantec AntiVirus Corporate Edition 10.1 installed.
And I have excluded the following folders from scanning:

C:\WINDOWS\NTDS
C:\WINDOWS\ntfrs\jet\sys
C:\WINDOWS\security
C:\WINDOWS\SYSVOL

C:\WINDOWS\system32\config
C:\WINDOWS\system32\dhcp
C:\WINDOWS\system32\spool
C:\WINDOWS\system32\dns
C:\WINDOWS\system32\inetsrv
C:\WINDOWS\system32\CatRoot2
C:\WINDOWS\system32\wins

C:\Program Files\Exchsrvr
C:\Program Files\Microsoft SQL Server
D:\Exchange\mdbdata\

And Yes I have Indexing Service allowed.
Disable indexing, if not for the whole drive, then at least for the DHCP folder

-red

Author

Commented:
Indexing disabled, will report findings.
Principal Consultant
Most Valuable Expert 2016
Top Expert 2014
Commented:
Also, please check to make sure that the SYSTEM account has full permissions for C:\windows\system32\dhcp\backup

Jeff
TechSoEasy

Author

Commented:
SYSTEM account has inherited full permissions for C:\windows\system32\dhcp\backup

Author

Commented:
I have not had this reported error so all appears well.  Thanks!
Should I enable Indexing again?
I don't think you should enable indexing again, but you could try.

Why did you accept the answer here when it was not the solution?

I think the points for this question should be reduced to zero (as this is pretty much a duplicate -> http://www.experts-exchange.com/Operating_Systems/SBS_Small_Business_Server/Q_22110230.html#a18248284) , and a correct answer accepted instead.

-red
Jeffrey Kane - TechSoEasyPrincipal Consultant
Most Valuable Expert 2016
Top Expert 2014

Commented:
Indexing has to be enabled if you're running CRM on that server.

Jeff
TechSoEasy
Event Type: Error
Event Source: DhcpServer
Event Category: None
Event ID: 1016
Description:
The DHCP service encountered the following error when backing up the database:
An error occurred while accessing the DHCP database. Look at the
DHCP server event log for more information on this error.
Resolution:
1. Disable Allow Indexing Service to index this disk for fast file searching. To do that, open the properties of the C. Select General. Uncheck the Allow Indexing Service to index this disk for fast file searching.
2. It could a software issue, for example Anti-virus and security software. You may try to Windows clean boot to test it.
3. Copy the original Windows system.md_ file from the Windows compact disc to your hard drive. Then, run the <Systemroot>\\System32\\Expand.exe program to expand System.md_ to System.mdb. Next, copy System.mdb to the new database location.
4. Or refer to the following links:
Event Viewer Displays DHCP Events 1010, 1016, and 1014
... The DHCP server encountered the following error when cleaning up the user database -or- DHCP Event 1016 ... Article ID : 129730: Last Review : November 1, 2006: Revision : 4.1
http://support.microsoft.com/kb/129730
we are getting the same event error 1010, 1014, 1016 on my domain controller and also DHCP SERVER.
WE are having Macfee antivirus installed on server.
indexing are enabled on server.
System32 having full permission.

However my question is that i have 14 domain controller in my parent and child domain and all are having same settings then why its giving me this error.

if i disabled indexing from c drive then what other cause for OS and AD and if i do this only for testing then shall i able to enable it again.

What else i need to do with antivirus part?

I m surprising as all other domain controller having same settings and running fine ?

Please provide me the solution, its urgent for me.
Jeffrey Kane - TechSoEasyPrincipal Consultant
Most Valuable Expert 2016
Top Expert 2014

Commented:
If you have 14 domain controllers in your domain then you have a completely different problem and should post a new question in the appropriate zone.  This question is referring to a Small Business Server installation.

Jeff
TechSoEasy

Commented:
i am just getting the error mesasge with event Id:-1010 ,1014 and 1016 with DHCP i have already disable the indexing so please insure after the disable it proble will be resolve or not ?

Do more with

Expert Office
Submit tech questions to Ask the Experts™ at any time to receive solutions, advice, and new ideas from leading industry professionals.

Start 7-Day Free Trial