?
Solved

Cisco 1721 IOS upgrade

Posted on 2007-03-25
2
Medium Priority
?
4,064 Views
Last Modified: 2008-07-10
I have a Cisco 1721 with an IOS of 12.3 . I upgraded the IOS with the image c1700-k9o3sy7-mz.123-15 to 12.3 but the system crashed on startup with the following error. I had to use xmodem to reload the old IOS. How can I resolve the error below


################################################################################
########################################################################### [OK]



Smart Init is enabled
smart init is sizing iomem
  ID            MEMORY_REQ         TYPE
MainBoard       0X00027A80 1721
                0X000F3BB0 public buffer pools
                0X00211000 public particle pools
0X0002          0X0000DC00 Card in slot 0
0X0039          0X0000DC00 Card in slot 1
TOTAL:          0X00347E30

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.



Memory required: 42752540 bytes, Memory available: 33554432 bytes
INSUFFICIENT MEMORY TO LOAD IMAGE!
The difference between Memory required and Memory available is the additional
memory you need to run the router. Alternately, use a smaller image; this
may cause the memory requirement to decrease, and may allow you to at least
use the router with reduced functionality until you get more memory.


*** System received a Software forced crash ***
signal= 0x17, code= 0x200, context= 0x8000630c
PC = 0xffffffff, Vector = 0x200, SP = 0xffffffff

System Bootstrap, Version 12.2(7r)XM1, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2001 by cisco Systems, Inc.
C1700 platform with 32768 Kbytes of main memory

program load complete, entry point: 0x80008000, size: 0x9624d8
Self decompressing the image : #################################################
################################################################################
########################### [OK]


Smart Init is enabled
smart init is sizing iomem
  ID            MEMORY_REQ         TYPE
MainBoard       0X00027A80 1721
                0X000F3BB0 public buffer pools
                0X00211000 public particle pools
0X0002          0X0000DC00 Card in slot 0
0X0039          0X0000DC00 Card in slot 1
TOTAL:          0X00347E30

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.



Memory required: 42752540 bytes, Memory available: 33554432 bytes
INSUFFICIENT MEMORY TO LOAD IMAGE!
The difference between Memory required and Memory available is the additional
memory you need to run the router. Alternately, use a smaller image; this
may cause the memory requirement to decrease, and may allow you to at least
use the router with reduced functionality until you get more memory.


*** System received a Software forced crash ***
signal= 0x17, code= 0x200, context= 0x8000630c
PC = 0xffffffff, Vector = 0x200, SP = 0xffffffff

System Bootstrap, Version 12.2(7r)XM1, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2001 by cisco Systems, Inc.
C1700 platform with 32768 Kbytes of main memory

rommon 1 > ?
0
Comment
Question by:it_gsr
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
2 Comments
 
LVL 1

Expert Comment

by:kkwatai
ID: 18789456
I see the message INSUFFICIENT MEMORY TO LOAD IMAGE!

Have you considered the possibility that you loaded an IOS that is too big for your router to handle? It looks like you only have 32MB RAM when your IOS image requires 42ish.

http://www.cisco.com/en/US/products/hw/routers/ps221/products_installation_guide_chapter09186a00801a0900.html

for upgrade instructions.
0
 

Accepted Solution

by:
countjugular earned 750 total points
ID: 20277543
Hi, "INSUFFICIENT MEMORY TO LOAD IMAGE!" appears to be your problem.... I just ran into this myself a few weeks ago... here's the site that showes the cisco part#, max memory ... etc ... hope it helps

http://www.cisco.com/en/US/docs/routers/access/1700/1720/hardware/notes/1700UMem.html
0

Featured Post

Simple, centralized multimedia control

Watch and learn to see how ATEN provided an easy and effective way for three jointly-owned pubs to control the 60 televisions located across their three venues utilizing the ATEN Control System, Modular Matrix Switch and HDBaseT extenders.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

While it is possible to put two routes in place with the secondary having a higher metric, this may not always work. In the event of a failure that does not bring down the physical interface on the router the primary route is not removed. There is a…
We've been using the Cisco/Linksys RV042 for years as: - an internet Gateway - a site-to-site VPN device - a leased line site-to-site subnet-to-subnet interface (And, here I'm assuming that any RV0xx behaves the same way as an RV042.  So that's …
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses

764 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question