Solved

Pix 6.3 to 7.0 migration - command not working

Posted on 2007-03-27
4
443 Views
Last Modified: 2010-08-05
I was able to just copy and paste the 6.3 config into 7.0 and it worked fine for the most part. The commands that are giving me error are the following (pasting output below)

Is there anyway to get around it? If this can't be done, what would I miss from the old config from the users standpoint? Thanks for your time.

hostname(config)# vpdn group PPTP-VPDN-GROUP accept dialin pptp
ERROR: % This command is an unreleased and unsupported feature

hostname(config)# vpdn group PPTP-VPDN-GROUP ppp authentication pap
ERROR: % This command is an unreleased and unsupported feature

hostname(config)# vpdn group PPTP-VPDN-GROUP ppp authentication chap
ERROR: % This command is an unreleased and unsupported feature

hostname(config)# vpdn group PPTP-VPDN-GROUP ppp authentication mschap
ERROR: % This command is an unreleased and unsupported feature

hostname(config)# vpdn group PPTP-VPDN-GROUP ppp encryption mppe 128
ERROR: % This command is an unreleased and unsupported feature

hostname(config)# vpdn group PPTP-VPDN-GROUP client configuration address local RASVPN
ERROR: % This command is an unreleased and unsupported feature

hostname(config)# vpdn group PPTP-VPDN-GROUP client configuration dns 10.1.44.12
ERROR: % This command is an unreleased and unsupported feature

hostname(config)# vpdn group PPTP-VPDN-GROUP pptp echo 60
ERROR: % This command is an unreleased and unsupported feature

hostname(config)# vpdn group PPTP-VPDN-GROUP client authentication local
ERROR: % This command is an unreleased and unsupported feature

hostname(config)# vpdn enable outside
ERROR: % This command is an unreleased and unsupported feature

hostname(config)# vpdn enable inside
ERROR: % This command is an unreleased and unsupported feature
0
Comment
Question by:jibranilyas
  • 2
  • 2
4 Comments
 
LVL 19

Expert Comment

by:nodisco
Comment Utility
Hey there

Unfortunately the bad news is that 7.X does not support pptp termination.  Your options would be to setup an internal pptp server and allow traffic through the PIX to it, or use Cisco VPN client.

http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_tech_note09186a00804708d8.shtml

Under the prerequisites ^

sorry to bear the bad news

hth
0
 

Author Comment

by:jibranilyas
Comment Utility
Thanks. So as far as the users are concerned, what will they miss after this transition?
0
 
LVL 19

Accepted Solution

by:
nodisco earned 500 total points
Comment Utility
All the commands listed above are all to do with pptp termination.  So the PIX will perform its functions per before with the one exception that Microsoft PPTP clients that used to connect to the PIX outside ip address will no longer be able to do this.  
The Cisco VPN client is a far more secure connection method and is the recommended vpn client to use

hth
0
 

Author Comment

by:jibranilyas
Comment Utility
Great!
Thank you so much
0

Featured Post

VMware Disaster Recovery and Data Protection

In this expert guide, you’ll learn about the components of a Modern Data Center. You will use cases for the value-added capabilities of Veeam®, including combining backup and replication for VMware disaster recovery and using replication for data center migration.

Join & Write a Comment

From Cisco ASA version 8.3, the Network Address Translation (NAT) configuration has been completely redesigned and it may be helpful to have the syntax configuration for both at a glance. You may as well want to read official Cisco published AS…
This is an article about my experiences with remote access to my clients (so that I may serve them) and eventually to my home office system via Radmin Remote Control. I have been using remote access for over 10 years and have been improving my metho…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
In this tutorial you'll learn about bandwidth monitoring with flows and packet sniffing with our network monitoring solution PRTG Network Monitor (https://www.paessler.com/prtg). If you're interested in additional methods for monitoring bandwidt…

772 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

10 Experts available now in Live!

Get 1:1 Help Now