Solved

How do I configure the PIX 501 to allow the necessary ports to  allow Remote Work Webplace, etc.?

Posted on 2007-03-28
3
294 Views
Last Modified: 2010-04-09
OK, I have read every answer on setting up Remote Web Workplace , and I have read the suggested reading by TechSoEasy (which I have found it is not -- although I love it). But, I just can't seem to be able to configure my Cisco PIX to allow the ports to point to the server if that is the right terminology. If I am reading and understanding some of it correctly, I need to open ports 25, 80, 443, 444, and 4125. My guess is port 25 is already available since I can receive email?

Currently, I am running SBS 2003 Standard with one NIC and, therefore, no firewall. I have Internet provided by Time-Warner cable with a static IP address runing through a PIX 501 firewall/router which is defaultly configured. It is set up to use PAT rather than NAT so I do not know if that is correct -- but it works fine. All of the work stations are set up to obtain their IP addresses, etc. via DHCP, and the server is the DHCP server.

So, how do I configure the PIX to allow me to access the Remote Web Workplace, Outlook and Sharepoint? Please assume I know nothing about how to configure the Cisco router and am completely stupid when it comes to using the command interface. In fact, if I had to use the command interface, I would most likely need to find a friend who can configure a PIX or have Jeff connect remotely, Jeff being TechSoEasy who always helps me a lot and most likely knows my lack of knowledge when it comes to the Cisco router and SBS.  If possible, can it be done using the PIX PDM?

PIX Version: 6.3(5)   PDM Version: 3.0(4)
0
Comment
Question by:Bert2005
  • 3
3 Comments
 
LVL 15

Expert Comment

by:plimpias
ID: 18813775
Hello,

You will need to configure a port map rule on your pix for port 4125

Log into PIX

config t
static (inside,outside) tcp interface RWW 192.168.1.X RWW netmask
255.255.255.255 0 0
0
 
LVL 15

Accepted Solution

by:
plimpias earned 500 total points
ID: 18813790
0
 
LVL 15

Expert Comment

by:plimpias
ID: 18813799
If you do a show config command on the pix. you should see the the existing configuration. You can get an idea of the command santax in that.
0

Featured Post

Windows Server 2016: All you need to know

Learn about Hyper-V features that increase functionality and usability of Microsoft Windows Server 2016. Also, throughout this eBook, you’ll find some basic PowerShell examples that will help you leverage the scripts in your environments!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

I recently updated from an old PIX platform to the new ASA platform.  While upgrading, I was tremendously confused about how the VPN and AnyConnect licensing works.  It turns out that the ASA has 3 different VPN licensing schemes. "site-to-site" …
I’m often asked about newer and larger USB drives connected to SBS2008 and 2011 failing Windows Server Backup vs the older USB drives not failing. As disk space continues to grow and drive technology change SBS2008 and some SBS2011 end up with the f…
As a trusted technology advisor to your customers you are likely getting the daily question of, ‘should I put this in the cloud?’ As customer demands for cloud services increases, companies will see a shift from traditional buying patterns to new…
Both in life and business – not all partnerships are created equal. Spend 30 short minutes with us to learn:   • Key questions to ask when considering a partnership to accelerate your business into the cloud • Pitfalls and mistakes other partners…

770 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question