Solved

Configure Port forwarding on CISCO PIX 501

Posted on 2007-04-11
7
240 Views
Last Modified: 2010-04-09
I want to be able to configure Cisco 501 to port forward the following using telenet commands.

My telenet knowledge little or none

Port 25 to 192.168.0.X
Port 21 to 192.168.0.X
Port 1719 to 192.168.0.x

I need to be able to do this using telnet.

I have little or no experience with Telnet please help me as much

Nazmul
0
Comment
Question by:X-quisite
  • 4
  • 3
7 Comments
 
LVL 29

Expert Comment

by:Alan Huseyin Kayahan
ID: 18892715
           Hi X-quisite
              *First of all let me ask you some questions. Are you now able to connect to PIX CLI via telnet?
              *Is there a NAT or PAT configured?
              *Can you post running config here?

Regards
0
 

Author Comment

by:X-quisite
ID: 18894842
Mr Husy,

I can connect to the pix CLI via Telnet
No PAT or NAT is configured, actually nothing is configured, still at factory default.
What do you mean by “running config” ? Sorry to sound stupid?
0
 
LVL 29

Accepted Solution

by:
Alan Huseyin Kayahan earned 500 total points
ID: 18896873
        When you type sh run, your running config of PIX appear but no use if it is at factory default.
         Following link will guide you through some basics. Please ask if you dont understand steps.
http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_61/config/bafwcfg.htm
0
PRTG Network Monitor: Intuitive Network Monitoring

Network Monitoring is essential to ensure that computer systems and network devices are running. Use PRTG to monitor LANs, servers, websites, applications and devices, bandwidth, virtual environments, remote systems, IoT, and many more. PRTG is easy to set up & use.

 

Author Comment

by:X-quisite
ID: 18924070
Mr Hussy,

Thank you for the link.
There two interfaces on the PIX
1)If my internal network ip Range is 192.168.0.0 should i configure the interbal interface to have a static IP address of say 192.168.0.1

2) What should i configure the external interface to be?
I have static WAN IP Adress from my ISP
Also i am using an ethernet modem which has an IP address of 192.168.1.1 and configured as bridged, with a DHCP server.

What i am confused about is should i configure the static WAN IP address on the external interface or an static IP address of say 192.168..1.2 which is of the same range of the ethernet modem?

Nazmul

0
 
LVL 29

Expert Comment

by:Alan Huseyin Kayahan
ID: 18925573
          Hi Nazmul
           1) Yes, you should assign a static IP address for inside interface of PIX. 192.168.1.1 is the default one.
           2)If your global IP address is assigned to your ethernet modem, and you reach internet with 192.168.1.1 gateway, then you should assign an ip to your outside interface in this network. If this global IP is by a router or other ISP device, then you should assign that ip to the outside interface of your PIX.
           

Regards
0
 
LVL 29

Expert Comment

by:Alan Huseyin Kayahan
ID: 19168211
          Hi Nazmul
                Would you please explain why you graded C?

Regards
0
 

Author Comment

by:X-quisite
ID: 19168242
Mr Hussy,

I did not get the answer i was looking for although the document link you provided was helpful.

Nazmul
0

Featured Post

VMware Disaster Recovery and Data Protection

In this expert guide, you’ll learn about the components of a Modern Data Center. You will use cases for the value-added capabilities of Veeam®, including combining backup and replication for VMware disaster recovery and using replication for data center migration.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Cisco / asa /Nagios 3 15
Not able to route between subnets 8 104
Cisco ASDM migration 2 19
Cisco UCS: C-Series, bios failed power-on self test 2 21
Overview The Cisco PIX 501, PIX 506e, ASA 5505 and ASA 5510 (most if not all of this information will be relevant to the PIX 515e but I do not have a working configuration handy to verify the validity) are primarily used within small to medium busi…
Have you experienced traffic destined through a Cisco ASA firewall disappears and you do not know if the traffic stops in the firewall or somewhere else? The solution is the capture feature. This feature was released in 6.2(1) and works in all firew…
Both in life and business – not all partnerships are created equal. As the demand for cloud services increases, so do the number of self-proclaimed cloud partners. Asking the right questions up front in the partnership, will enable both parties …
As a trusted technology advisor to your customers you are likely getting the daily question of, ‘should I put this in the cloud?’ As customer demands for cloud services increases, companies will see a shift from traditional buying patterns to new…

920 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

12 Experts available now in Live!

Get 1:1 Help Now