Link to home
Start Free TrialLog in
Avatar of DCSD
DCSDFlag for United States of America

asked on

Setting up T1 between 2 cisco 1700's

Setting up T1 between 2 cisco 1700's, but I am unable to get this working here are the errors i'm pulling thru "show service-module"

Module type is T1/fractional
    Hardware revision is 0.88, Software revision is 20040131-0.3,
    Image checksum is 0x873E3B7E, Protocol revision is 0.1
Transmitter is sending remote alarm.
Receiver has loss of signal, loss of frame,
Framing is ESF, Line Code is B8ZS, Current clock source is line,
Fraction has 24 timeslots (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec.
Last module self-test (done at startup): Passed
Last clearing of alarm counters 01:39:58
    loss of signal        :    1, current duration 01:39:50
    loss of frame         :    1, current duration 01:39:50
    AIS alarm             :    0,
    Remote alarm          :    0,
    Module access errors  :    0,
Total Data (last 6 15 minute intervals):
    8 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 5400 Fr Loss Secs, 1 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 5400 Unavail Secs
Data in current interval (589 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 589 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 589 Unavail Secs

Here is my config on the 1700.

Version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service udp-small-servers
service tcp-small-servers
!
hostname X_X
!
boot-start-marker
boot-end-marker
!
enable password xxxxxxx
!
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
no aaa new-model
ip subnet-zero
!
no ip domain lookup
!
ip cef
!
interface FastEthernet0/0
 ip address x.x.x.x x.x.x.x
 speed 100
 full-duplex
 ipx network 16F11 encapsulation SAP
!
interface Serial0/0
 description X_X
 ip address x.x.x.x x.x.x.x
 ip ospf network point-to-multipoint
 autodetect encapsulation ppp
 ipx network 16
!
router ospf 1
 log-adjacency-changes
 network x.x.0.0 0.0.x.x area 0
!
ip classless
ip route 0.0.0.0 0.0.0.0 x.x.x.x
ip route 0.0.0.0 0.0.0.0 x.x.x.x
ip http server
!
end
Avatar of Les Moore
Les Moore
Flag of United States of America image

>autodetect encapsulation ppp
Change this to just
 encap ppp

If this is a dedicated T1, one end should provide clocking:
 
interface serial 0/0
  service-module t1 clock source internal

The other one can remain default clock source line
Are you getting any errors on the interface? Show interface ser 0/0
Avatar of DCSD

ASKER

no errors on the serial interface.

On the clock rate do I need to set that manually or can I just use
"service-module t1 clock source internal".

thanks
Unless specified, it will default to the standard clock rate of the T1 module which is fine.
If you are not getting any error counters, then you might want to hold off on setting the clock source.
Can you post result of "show interface serial 0/0"

Avatar of DCSD

ASKER

Serial0/0 is down, line protocol is down
  Hardware is PQUICC with Fractional T1 CSU/DSU
  Description: JHS_NOC
  Internet address is X.X.X.X/30
  MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation PPP, LCP Closed, loopback not set
  Keepalive set (10 sec)
  Last input never, output never, output hang never
  Last clearing of "show interface" counters 00:38:09
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: weighted fair
  Output queue: 0/1000/64/0 (size/max total/threshold/drops)
     Conversations  0/0/256 (active/max active/max total)
     Reserved Conversations 0/0 (allocated/max allocated)
     Available Bandwidth 1158 kilobits/sec
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions
     DCD=down  DSR=up  DTR=up  RTS=up  CTS=down
>Serial0/0 is down, line protocol is down
Well, this is not good at all. Have you contacted the Telco support and told them that you have the CPE connected and are ready to activeate the T1?
Avatar of DCSD

ASKER

Yeah they say there end is fine, but I've played this blame game junk before w/ telco's, vendors, etc...

I'll get w/ them on monday.... Thanks for the help
How are you connected to the smart jack? By standard CAT5 patch cable?
Avatar of DCSD

ASKER

yes
Are both ends connected, powered on and ready?
Avatar of DCSD

ASKER

Yup
I would demand second level support. Make sure they understand that you can't even see Carrier Detect.
Avatar of DCSD

ASKER

Yes straight thru cat 5
Avatar of DCSD

ASKER

So I should be getting Carrier Detect even if my clocking is off?
Yes, unless your channel assignment is off. Are you sure you have all 24 channels of a full T1?
Avatar of DCSD

ASKER

Appears Verizon had problems, but I am still reciveing "line protocol is down (looped)"?


Serial0/0 is up, line protocol is down (looped)
  Hardware is PQUICC with Fractional T1 CSU/DSU
  Description: XXX
  Internet address is X.X.X.X/X
  MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
     reliability 252/255, txload 1/255, rxload 1/255
  Encapsulation PPP, LCP REQsent, loopback not set
  Keepalive set (10 sec)
  Last input 00:00:01, output 00:00:01, output hang never
  Last clearing of "show interface" counters 1d01h
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: weighted fair
  Output queue: 0/1000/64/0 (size/max total/threshold/drops)
     Conversations  0/1/256 (active/max active/max total)
     Reserved Conversations 0/0 (allocated/max allocated)
     Available Bandwidth 1158 kilobits/sec
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     29330 packets input, 410620 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     2068 input errors, 0 CRC, 2005 frame, 0 overrun, 0 ignored, 63 abort
     29330 packets output, 410620 bytes, 0 underruns
     0 output errors, 0 collisions, 4486 interface resets
     0 output buffer failures, 0 output buffers swapped out
     1 carrier transitions
ASKER CERTIFIED SOLUTION
Avatar of Les Moore
Les Moore
Flag of United States of America image

Link to home
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
Start Free Trial
Avatar of DCSD

ASKER

It was a verizon issue the line is up.

Thank you for your help.