Want to protect your cyber security and still get fast solutions? Ask a secure question today.Go Premium

x
?
Solved

2620xm IOS code, BGP and nm-hdv2 support

Posted on 2007-08-12
8
Medium Priority
?
723 Views
Last Modified: 2010-08-05
I was upgrading my routers (2620xm, 32flash/96mem) this weekend to new MPLS circuits running BGP. My ios on the routers does not support BGP (currently on ip-voice-c2600-12.3(8)T5). I downloaded spservices and installed it, but it did not support the nm-hdv2 module in the routers going to the phone switch. I have found that an older version of ip voice will work, but cannot find a copy of it. It has been pulled from Cisco's site due to vulnerabilities in the code. I need ip voice for a 2620XM version 12.3(2)T9 or earlier. Can anyone help me out here?

Thank you!
0
Comment
Question by:pbenningfield
  • 4
  • 4
8 Comments
 
LVL 7

Expert Comment

by:logic2
ID: 19687351
usually the Enterprise IOS version should have everything in it
If you have 32M flash then go for
c2600-adventerprisek9-mz.124-16.bin   or
c2600-adventerprisek9-mz.123-23.bin

Theoritically any of the above should work fine
however the latest IP Voice from Cisco is c2600-ipvoicek9-mz.124-16.bin, dont think that it supports BGP

So try the above two and tell me the results
0
 
LVL 2

Author Comment

by:pbenningfield
ID: 19688998
Hi,

c2600-adventerprisek9-mz.124-16.bin requires 128 mb memory; I have applied c2600-adventerprisek9-mz.123-23.bin and get the following on a show diag:

Slot 1:
        Unknown (type 986) Port adapter
        Port adapter is disabled
        Port adapter insertion time unknown
        EEPROM contents at hardware discovery:
        Hardware Revision        : 1.1
        Top Assy. Part Number    : 800-22167-01
        Board Revision           : A0
        Deviation Number         : 0
        Fab Version              : 04
        PCB Serial Number        : FOC083018WX
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Fab Part Number          : 28-6126-04
        Manufacturing Test Data  : 00 00 00 00 00 00 00 00
        Field Diagnostics Data   : 00 00 00 00 00 00 00 00
        Product (FRU) Number     : NM-HDV2-1T1/E1
        Version Identifier (VID) : V01
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 03 DA 41 01 01 C0 46 03 20 00 56 97 01
          0x10: 42 41 30 88 00 00 00 00 02 04 C1 8B 46 4F 43 30
          0x20: 38 33 30 31 38 57 58 03 00 81 00 00 00 00 04 00
          0x30: 85 1C 17 EE 04 C4 08 00 00 00 00 00 00 00 00 C5
          0x40: 08 00 00 00 00 00 00 00 00 CB 8E 4E 4D 2D 48 44
          0x50: 56 32 2D 31 54 31 2F 45 31 89 56 30 31 20 D9 02
          0x60: 40 C1 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Thanks,

Trish
0
 
LVL 7

Expert Comment

by:logic2
ID: 19690576
Ok i guess this was just a quick shot from me
I searched on Cisco and apparently the only IOS that supports this module is the 12.3(7)T and later starting from the IP Plus versions
so in that case i would guess that any 12.3 T would do the trick again go for the enterprise version
Check this document

http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a008039c333.shtml
The only one i found matching your ram is c2600-entbase-mz.123-14.T7.bin
I hope it fixes everything
0
Evaluating UTMs? Here's what you need to know!

Evaluating a UTM appliance and vendor can prove to be an overwhelming exercise.  How can you make sure that you're getting the security that your organization needs without breaking the bank? Check out our UTM Buyer's Guide for more information on what you should be looking for!

 
LVL 2

Author Comment

by:pbenningfield
ID: 19693595
Thanks... tried c2600-entbase-mz.123-14.T7.bin   still getting the following:
Slot 1:
        Unknown (type 986) Port adapter
        Port adapter is disabled
        Port adapter insertion time unknown
        EEPROM contents at hardware discovery:
        Hardware Revision        : 1.1
        Top Assy. Part Number    : 800-22167-01
        Board Revision           : A0
        Deviation Number         : 0
        Fab Version              : 04
        PCB Serial Number        : FOC083018WT
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Fab Part Number          : 28-6126-04
        Manufacturing Test Data  : 00 00 00 00 00 00 00 00
        Field Diagnostics Data   : 00 00 00 00 00 00 00 00
        Product (FRU) Number     : NM-HDV2-1T1/E1
        Version Identifier       : V01
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 03 DA 41 01 01 C0 46 03 20 00 56 97 01
          0x10: 42 41 30 88 00 00 00 00 02 04 C1 8B 46 4F 43 30
          0x20: 38 33 30 31 38 57 54 03 00 81 00 00 00 00 04 00
          0x30: 85 1C 17 EE 04 C4 08 00 00 00 00 00 00 00 00 C5
          0x40: 08 00 00 00 00 00 00 00 00 CB 8E 4E 4D 2D 48 44
          0x50: 56 32 2D 31 54 31 2F 45 31 89 56 30 31 20 D9 02
          0x60: 40 C1 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Hunting around through old archives, not finding anything, anyone have an old IP-VOICE out there with BGP support?

Thanks,

Trish

0
 
LVL 7

Expert Comment

by:logic2
ID: 19696907
Thats strange
the problem is that i couldnt find the exact 12.3(7)T on Cisco's website
Do you have a cisco partner account ? if thats the case then maybe opening a Cisco TAC will help
My last options in this are the 2 below IOSs not sure if they'd support your card but i know they support other voice cards

c2600-adventerprisek9-mz.123-11.T7
c2600-is-mz.122-15.T13
0
 
LVL 2

Author Comment

by:pbenningfield
ID: 19696946
Thanks.  We don't have a smartnet on this equipment and although I will buy one now, it will be weeks before it kicks in... Cisco is not being at all helpful, only saying "that should work" in regard to spservices...  Seems only c2600-ipvoice supports this card from what I can find, but ipvoice had BGP removed for whatever the reason, and the code I need is retired...  Have tried adventerprisek9, will look at c2600-is-mz next.  Thanks...
0
 
LVL 7

Expert Comment

by:logic2
ID: 19698248
Strange you are saying that Cisco isnt helpful
They are always helpful well at least with my company
0
 
LVL 2

Accepted Solution

by:
pbenningfield earned 0 total points
ID: 20060720
Apologies for leaving this open so long.  I was able to resolve it by upgrading the memory in all the routers and then the code supported BGP as well as the voice module card.
0

Featured Post

Evaluating UTMs? Here's what you need to know!

Evaluating a UTM appliance and vendor can prove to be an overwhelming exercise.  How can you make sure that you're getting the security that your organization needs without breaking the bank? Check out our UTM Buyer's Guide for more information on what you should be looking for!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Did you know that more than 4 billion data records have been recorded as lost or stolen since 2013? It was a staggering number brought to our attention during last week’s ManageEngine webinar, where attendees received a comprehensive look at the ma…
2017 was a scary year for cyber security.  Hear what our security experts say that hackers have in store for us in 2018.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

572 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question