Solved

Setting up POP3 on 2K7 Exchange

Posted on 2007-11-29
4
410 Views
Last Modified: 2013-11-29
I have a new 2K7 Exch server and I need to setup POP3 I have found an article below but there are some items in the solution that I am not sure off.  My clients are Outlook Express 6.  

In question 2 how do I know which one to use a or b and what is the IP adderss:port that I should use.

Any help would be appreciated.


1. Set MSExchangePOP3 service to automatic - I HAVE SET THE POP3 TO AUTOMATIC
Set-service msExchangePOP3 -startuptype automatic

2.Configure IP Address and Port for POP3

a.To set the IP address and port for communicating with Exchange using POP3 with SSL, run the following command:
    Set-PopSettings -SSLBindings: IPaddress:Port

b.To set the IP address and port for communicating with Exchange using POP3 with no encryption or Transport Layer Security (TLS) encryption,    
    Set-PopSettings -UnencryptedOrTLSBindings IPaddress:Port

3.Configure POP3 Authentication - POP3 (110) /POP3 SSL (995)

a.If you will not be using TLS encryption and you want to allow Basic authentication on an unsecured port, run the following command:
   Set-PopSettings -LoginType PlainTextLogin

b.If you will not be using TLS, but you want to restrict Basic authentication to use only secured ports, run the following command:
   Set-PopSettings -LoginType PlainTextAuthentication

c.If you want to use TLS encryption before authentication, run the following command:
   Set-PoPSettings -LoginType SecureLogin

4.Enable POP3 Protocol for the User Mailbox

Set-CasMailbox MailboxName -Popenabled:$true

5.Configure the SMTP Receive Connector on the Exchange Server to Allow Anonymous in order to send Email using the following command:
Set-ReceiveConnector "Servername\default Servername" -PermissionGroups
“ExchangeServers,ExchangeUsers,ExchangeLegacyServers,AnonymousUsers"

6.Restart the Microsoft Exchange POP3 Service
   Restart-service MSExchangepop3

0
Comment
Question by:mpage
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
  • 2
4 Comments
 
LVL 15

Expert Comment

by:JimboEfx
ID: 20375172
Shooting from the hip here:

but the ports are in the article?

 POP3 (110) /POP3 SSL (995)

so

-SSLBindings: x.x.x.x:995

or

UnencryptedOrTLSBindings  x.x.x.x:110

where x.x.x.x is an address on a network interface attached to the server?

110 and 995 being the standard ports for these services, but configurable by my guess.
 
0
 

Author Comment

by:mpage
ID: 20376952
Thanks that seemed to work. On number 5 command, I am not sure what goes in this section.  The name of my exch 07 server is sdexch, at 10.1.1.107, should it be

Set-Receiveconnector "sdexch" -PermissionGroups "sdexch" ????

Your help is greatly appreciated

Set-ReceiveConnector "Servername\default Servername" -PermissionGroups
"ExchangeServers,ExchangeUsers,ExchangeLegacyServers,AnonymousUsers"

0
 
LVL 15

Accepted Solution

by:
JimboEfx earned 500 total points
ID: 20377102
The name is the name of the connector on the hub transport role. You could use get-receiveconnector to list them all.

The Permissions on the connector can be seen and changed in the GUI -
http://msexchangeteam.com/archive/2006/11/17/431555.aspx

The syntax of the command and an example can be seen here:

http://technet.microsoft.com/en-us/library/bb125140.aspx
0
 

Author Comment

by:mpage
ID: 20395519
Hey JimboEfx:
I did all three of these

a.If you will not be using TLS encryption and you want to allow Basic authentication on an unsecured port, run the following command:
   Set-PopSettings -LoginType PlainTextLogin

b.If you will not be using TLS, but you want to restrict Basic authentication to use only secured ports, run the following command:
   Set-PopSettings -LoginType PlainTextAuthentication

c.If you want to use TLS encryption before authentication, run the following command:
   Set-PoPSettings -LoginType SecureLogin

I only needed to do

a. set-PopSettings -LoginType PlainTextlogin
It is working now, some times I wonder if I have a brain.

If you have any comments about logging in this was I would appreciate them.

0

Featured Post

Best Practices: Disaster Recovery Testing

Besides backup, any IT division should have a disaster recovery plan. You will find a few tips below relating to the development of such a plan and to what issues one should pay special attention in the course of backup planning.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Outlook 2016 - Operation has failed 11 109
ADFS: AADSTS50107: Requested federation realm object 8 93
NLB +DAG 8 49
gmails for offline viewing 6 36
This process describes the steps required to Import and Export data from and to .pst files using Exchange 2010. We can use these steps to export data from a user to a .pst file, import data back to the same or a different user, or even import data t…
This article explains how to install and use the NTBackup utility that comes with Windows Server.
In this video we show how to create a Contact in Exchange 2013. We show this process by using the Exchange Admin Center. Log into Exchange Admin Center.: First we need to log into the Exchange Admin Center. Navigate to the Recipients >> Contact ta…
In this video we show how to create an email address policy in Exchange 2013. We show this process by using the Exchange Admin Center. Log into Exchange Admin Center.:  First we need to log into the Exchange Admin Center. Navigate to the Mail Flow…

739 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question