asked on

enter setup 2811

i enter the 2811 through console cable, it says SDM is installed use cisco cisco for username password. i want to use the IOS cli not SDM, how do i get past this : i am at
user access verification
username
password
when i use cisco, now i am at yourname#

maxis2cute

if you are going into the console and you see the # prompt ,that should be the privilage mode of the ios. The SDM is a web based management tool to help secure your router

jeffsteffy

ASKER

program load complete, entry point: 0x8000f000, size: 0xef3d74
Self decompressing the image : #################################################
################################################################################
########################## [OK]

Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0003E7 0X003DA000 C2811 Mainboard
0X000021B8 Onboard USB
0X002C29F0 public buffer pools
0X00211000 public
TOTAL: 0X008AFBA8

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 10Mb.
Using 3 percent iomem. [10Mb/256Mb]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(3i), RELEASE
SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 28-Nov-07 21:09 by stshen
Image text-base: 0x400A265C, data-base: 0x4154E2C0

Port Statistics for unclassified packets is not turned on.
Cisco 2811 (revision 49.46) with 251904K/10240K bytes of memory.
Processor board ID FTX1151A255
2 FastEthernet interfaces
2 Channelized (E1 or T1)/PRI ports
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
63808K bytes of ATA CompactFlash (Read/Write)

ip http secure-server
^
% Invalid input detected at '^' marker.

transport input telnet ssh
^
% Invalid input detecte

transport input telnet ssh
^
% Invalid input detected at '^' marker.

SETUP: new interface FastEthernet0/1 placed in "shutdown" state

Press RETURN to get started!

*Jan 27 21:51:18.243: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state t
o up
*Jan 27 21:51:18.243: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state t
o up
*Jan 27 21:51:19.243: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0/0, changed state to down
*Jan 27 21:51:19.243: %LINEPROTO-5-UPDOWN: Lin
et0/1, changed state to down
*Jan 27 21:51:20.531: %SYS-5-CONFIG_I: Configured from memory by console
*Jan 27 21:51:20.899: %SYS-5-RESTART: System restarted --
Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(3i), RELEASE
SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 28-Nov-07 21:09 by stshen
*Jan 27 21:51:20.903: %SNMP-5-COLDSTART: SNMP agent on host yourname is undergoi
ng a cold start
*Jan 27 21:51:22.531: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state
to administratively down
-----------------------------------------------------------------------
Cisco Router and Security Device Manager (SDM) is installed on this device.
This feature requires the one-time use of the username "cisco"
with the password "cisco". The default username and password have a privilege le
vel of 15.

Please change these publicly known initial credentials using SDM or the IOS CLI.

Here are the Cisco IOS commands.

username <myuser> privilege 15 secret 0 <mypassword>
no username cisco

Replace <myuser> and <mypassword> with the username and password you want to use
.

For more information about SDM please follow the instructions in the QUICK START

GUIDE for your router or go to http://www.cisco.com/go/sdm
-----------------------------------------------------------------------

User Access Verification

Username:

ASKER CERTIFIED SOLUTION

maxis2cute

membership

This solution is only available to members.

To access this solution, you must be a member of Experts Exchange.

Start Free Trial

jeffsteffy

ASKER

after cisco cisco
yourname#... is were i do enable secret <password>?
Is is my first router, i just started my 2nd CCNA class...so i am new.

jeffsteffy

ASKER

yourname#username 'myuser' privilege 15 secret 0 'mypassword'
%invalid input detedted at marker, under the s in username