Link to home
Create AccountLog in
Avatar of clarencumm
clarencummFlag for United States of America

asked on

I need to connect a pix 501E0 to a comcast cable modem and E1 to a cisco 2900/2950 switch to allow INTERNET access for several workstations. I sending all that I know how to do.

I would like to be able to connect to the INTERNET from one of the device attached to the switch if possible.  can I do it with the configuration that I'm using.  If not, what else is left to do???





interface ethernet0 100 full
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password CISCO
passwd cisco
hostname Blackwood Pix_501
domain-name ciscopix.com
clock timezone EST -5
clock summer-time EDT recurring
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol ils 389
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
names
access-list inside_outbound_nat0_acl permit ip any 10.1.200.0  255.255.0.0
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside 74.95.166.17 255.255.255.248
ip address inside 10.1.200.1 255.255.0.0
route outside 0.0.0.0 0.0.0.0  74.95.166.22
global (outside) 1 interface
global (outside) 1 74.95.166.17
nat ( inside) 1 10.1.200.0 255.255.0.0  0 0
nat (inside) 0 access-list inside_outbound_nat0_acl
access-list inside_access_in permit tcp any any
access-list inside_access_in permit icmp any any
access-list outside _access_in permit tcp any any
access-list outside _access_in permit icmp any any
ip audit info action alarm
ip audit attack action alarm
ip local pool LCI 10.1.15.1-10.1.15.10
pdm location 10.1.0.0 255.255.0.0 inside
pdm location 74.95.166.17  255.255.255.248 outside
pdm logging informational 100
pdm history enable
arp timeout 14400
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
http server enable
http 10.1.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-pptp
telnet 10.1.0.0 255.255.0.0 inside
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 5
console timeout 0
terminal width 80
Cryptochecksum:73ea2e261a4bfccd0faa506e08ab9ffd
: end

AUTO-SHEEN-CAR-WASH-Config2.bmp
Avatar of clarencumm
clarencumm
Flag of United States of America image

ASKER

I don't have too much experience with the pix 501, especially connecting one to the INTERNET without a Border router.  I would appreciate any recommendation . Thanks
Issue the following commands:

no access-list inside_outbound_nat0_acl permit ip any 10.1.200.0  255.255.0.0
no global (outside) 1 74.95.166.17
no nat (inside) 1 10.1.200.0 255.255.0.0
nat (inside) 1 0.0.0.0 0.0.0.0

See if that allows you to get to the Internet from internal hosts...
I will try this solution tomorrow and let you know what happens.  thanks
I just need to know how to connect my switch to the pix E1 interface.  Without the switch, everything works fine.  Thanks a lot
The only thing I can think of is that you have VLAN's configured on the switch.  Can you post the switch configuration here and let's have a look?
I haven't configured the switch. I'm not sure as how to go about it?
After more research, I discovered that the pix 501 cannot do trunking.  So,  I guess that I cannot use my switch to connect to the 501.  If this is the case, is there another way to connect more  than 4 (the # of E1 ports available on the 501) to the 501?  I'm at a lost now
ASKER CERTIFIED SOLUTION
Avatar of batry_boy
batry_boy
Flag of United States of America image

Link to home
membership
Create an account to see this answer
Signing up is free. No credit card required.
Create Account
Thanks,  I will try this today and let you know what happens.  
thanks again