Solved

CIsco OER Not Showing In-Policy

Posted on 2008-06-14
1
493 Views
Last Modified: 2011-08-18
I am trying to configure Cisco OER to control traffic across two links with OER. Both links are up, the master has routes to both links. The prefixes should eventually reflect In-Policy, Out of Policy or Holddown but they never move past default.

MASTER:
key chain teleport
 key 1
   key-string teleport
oer master
 policy-rules MAP_OER
 max-range-utilization percent 30
 logging
 !
 border 1.1.1.1 key-chain teleport
  interface FastEthernet0/0 internal
  interface Serial1/0 external
   max-xmit-utilization absolute 20
  interface Serial1/1 external
   max-xmit-utilization absolute 20
 !
 learn
  throughput
  delay
  periodic-interval 1
  monitor-period 1
 backoff 90 90
 mode route control
 mode select-exit best
periodic 180
resolve utilization priority 1 variance 2

ip prefix-list OER seq 5 permit 10.6.6.0/24 le 32
oer-map MAP_OER 10
 match ip address prefix-list OER
 set resolve utilization priority 1 variance 2
 set resolve range priority 2
 no set resolve delay

MASTER_OER#sh  oer master border
Border           Status   UP/DOWN             AuthFail
1.1.1.1          ACTIVE   UP       00:58:55          0

MASTER_OER#sh oer master pre
OER Prefix Statistics:
 Pas - Passive, Act - Active, S - Short term, L - Long term, Dly - Delay (ms),
 Los - Packet Loss (packets-per-million), Un - Unreachable (flows-per-million),
 E - Egress, I - Ingress, Bw - Bandwidth (kbps), N - Not applicable
 U - unknown, * - uncontrolled, + - control more specific, @ - active probe all

Prefix                  State     Time Curr BR         CurrI/F         Protocol
                      PasSDly  PasLDly   PasSUn   PasLUn  PasSLos  PasLLos
                      ActSDly  ActLDly   ActSUn   ActLUn      EBw      IBw
--------------------------------------------------------------------------------
10.6.6.0/24+         DEFAULT*       44 U               U

Routes:
   1.0.0.0/32 is subnetted, 1 subnets
O       1.1.1.1 [110/2] via 205.67.216.109, 00:48:01, FastEthernet0/0
     2.0.0.0/24 is subnetted, 1 subnets
O       2.2.2.0 [110/65] via 205.67.216.109, 00:48:01, FastEthernet0/0
     3.0.0.0/32 is subnetted, 1 subnets
C       3.3.3.3 is directly connected, Loopback0
     10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
O E2    10.6.6.0/24 [110/20] via 205.67.216.109, 00:48:02, FastEthernet0/0
O       10.6.6.6/32 [110/66] via 205.67.216.109, 00:48:02, FastEthernet0/0
     

===================================================
OER Border:
oer border
 local Loopback1
 master 3.3.3.3 key-chain teleport
ip route 10.6.6.0 255.255.255.0 Serial1/0
ip route 10.6.6.0 255.255.255.0 Serial1/1

     




0
Comment
Question by:klj_11566
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
1 Comment
 
LVL 32

Accepted Solution

by:
harbor235 earned 500 total points
ID: 21812854


Try adding "mode monitor passive" then repost "show oer master prefix"

Assumption, master router can route to 1.1.1.1 and back?

here is a good doc with example;

http://www.netcraftsmen.net/welcher/papers/oer02.html

harbor235 ;}
0

Featured Post

Free Tool: Port Scanner

Check which ports are open to the outside world. Helps make sure that your firewall rules are working as intended.

One of a set of tools we are providing to everyone as a way of saying thank you for being a part of the community.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Cable suggestions 5 77
Configure BGP 22 34
AS-Path BGP Attribute 7 27
can i use this ip range for my company 3 32
Introduction This article explores the design of a cache system that can improve the performance of a web site or web application.  The assumption is that the web site has many more “read” operations than “write” operations (this is commonly the ca…
In the world of WAN, QoS is a pretty important topic for most, if not all, networks. Some WAN technologies have QoS mechanisms built in, but others, such as some L2 WAN's, don't have QoS control in the provider cloud.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

756 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question