Solved

configuration check.

Posted on 2008-06-15
4
222 Views
Last Modified: 2011-10-19
I am currently setting up a small network with about 60 users. i have set up most of the local network and am waiting on a satlite dish to set up internet in a remote location. Basicly i am trying to figure out if my router config is going to work before the dish gets here, since i have never done this before.  

thanks.
putty.log
0
Comment
Question by:Justin Malone
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
4 Comments
 
LVL 8

Expert Comment

by:yasirirfan
ID: 21788063
what kind of router you are using ?
0
 
LVL 4

Author Comment

by:Justin Malone
ID: 21788083
Cisco 2610
(i also have a catalyst 2900 xl in the mix but the only thing configured on it is the vlans telnet and passwords.)
0
 
LVL 13

Expert Comment

by:kdearing
ID: 21788154
If everyone has a specific IP address, why not just use static IPs?
0
 
LVL 4

Accepted Solution

by:
Justin Malone earned 0 total points
ID: 21788214
because these are personal computers that will be used for more than just connecting to this network and i want to make it simple for them to connect and yet i also want to keep control over who connects. later i will add an access list that will block the remaining 15900 unused ip address.

mainly what im looking for in the nat configuration. assumeing i set up a satlite internet connection and assumeing that it passes a public address to my e0.0.1 interface and assumeing that i add working dns servers to the main dhcp pool will i be able to get online.

if needed i can post my switch config but i doubt it is nessessary my vlans work and all computers are receveing address via dhcp

currently the router is the main dhcp server, however i am setting up a domain controler that will eventualy take over that role. ill keep the config on the router and disable dhcp so i have a backup but thats about it.
0

Featured Post

Independent Software Vendors: We Want Your Opinion

We value your feedback.

Take our survey and automatically be enter to win anyone of the following:
Yeti Cooler, Amazon eGift Card, and Movie eGift Card!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
IPv6 question 1 75
Port forwarding 14 200
BGP prefix and routing 3 101
Usage of Prefix-List 5 77
It happens many times that access list (ACL) have to be applied to outgoing router interface in order to limit some traffic.This article is about how to test ACL from the router which is not very intuitive for everyone. Below scenario shows simple s…
There are two basic ways to configure a static route for Cisco IOS devices. I've written this article to highlight a case study comparing the configuration of a static route using the next-hop IP and the configuration of a static route using an outg…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

751 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question