Solved

Traffic-Shape Rate command

Posted on 2008-06-16
2
3,963 Views
Last Modified: 2012-06-21
I have a 20MB static line to the internet and have to provide the traffic shaping to avoind packet loss.  I am struggling with the command needed on the GB interface.

Here is what I have:
Interface GB0/0
 traffic-shape rate 20000000 500000 500000 1000

The command I entered however was simply
traffic-shape rate 20000000 and the rest was added automatically.  Is the above line proper for a 20MB internet connection.
0
Comment
Question by:vppinc
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
2 Comments
 
LVL 11

Accepted Solution

by:
rowansmith earned 500 total points
ID: 21809174
Is GB0/0 Connected to your ISP?  Does this interface have an IP Address assigned or is the IP Address on a sub-interface?

If so then this is configured correctly.  The remaining settings are set buy the IOS to allow you to maintain maximum throughput.

The format is:  traffic-shape rate bit-rate [burst-size [excess-burst-size]] [buffer-limit]

Bit-rate:
Bit rate that traffic is shaped to, in bits per second. This is the access bit rate that you contract with your service provider, or the service levels you intend to maintain. Bit rates can be in the range of 8000 to 100000000 bps.

burst-size:
(Optional) Sustained number of bits that can be sent per interval. On Frame Relay interfaces, this is the Committed Burst size contracted with your service provider. Valid entries are numbers in the range of 0 to 100000000.

excess-burst-size:
(Optional) Maximum number of bits that can exceed the burst size in the first interval in a congestion event. On Frame Relay interfaces, this is the Excess Burst size contracted with your service provider. Valid entries are numbers in the range of 0 to 100000000. The default is equal to the burst-size argument.

buffer-limit:
(Optional) Maximum buffer limit in bps. Valid entries are numbers in the range of 0 to 4096.

0
 

Author Closing Comment

by:vppinc
ID: 31467783
GB0/0 is connected to our ISP and the address is assigned to the physical interface.  Thanks for the info.
0

Featured Post

Enroll in June's Course of the Month

June's Course of the Month is now available! Every 10 seconds, a consumer gets hit with ransomware. Refresh your knowledge of ransomware best practices by enrolling in this month's complimentary course for Premium Members, Team Accounts, and Qualified Experts.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

While it is possible to put two routes in place with the secondary having a higher metric, this may not always work. In the event of a failure that does not bring down the physical interface on the router the primary route is not removed. There is a…
There are two basic ways to configure a static route for Cisco IOS devices. I've written this article to highlight a case study comparing the configuration of a static route using the next-hop IP and the configuration of a static route using an outg…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses

695 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question