Still celebrating National IT Professionals Day with 3 months of free Premium Membership. Use Code ITDAY17

x
?
Solved

bridge  configuration t1 setup no connection

Posted on 2008-06-21
7
Medium Priority
?
543 Views
Last Modified: 2013-12-12
I have 2 Blabk Box frame relay routers set up in a bridge configuration.  We were on the phone with ATT all day yesterday who claim to have setup our t1 line correctly and am looking for any advice as to how to go about configuring the black box correctly so we can get an ip address from our main office to this remote location.
0
Comment
Question by:Shanehaggerty
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 3
  • 2
7 Comments
 

Expert Comment

by:lltompkins
ID: 21839137
Would it not be easier to setup something like two Sonic Walls, even something Small like a TZ150.
You would be able to make a VPN connection and the sonicwalls are able to be configured so the one at the home office will pass IP Addresses to the computers at the second site.
0
 

Author Comment

by:Shanehaggerty
ID: 21839167
that is what i thought i was going to be able to do, so i am stuck with equipment i cannot use.  The way the isp ran our T1 line, we must make some kinda frame relay connection which i have no expierience doing in order to supposidley make this connection.
0
 

Expert Comment

by:lltompkins
ID: 21839694
check this out for basic information about Frame Relay.
http://www.protocols.com/pbook/frame.htm

Your provider should help you get the Frame Relay up and running.  
I would hammer on them until I got a working Circuit.  
0
Will your db performance match your db growth?

In Percona’s white paper “Performance at Scale: Keeping Your Database on Its Toes,” we take a high-level approach to what you need to think about when planning for database scalability.

 

Author Comment

by:Shanehaggerty
ID: 21865956
Turns out we had a broken circuit in one of two AT&T relay stations.  We had to agree to pay overtime wages for AT&T technicians to come in and help diagnose the problem.  (We are not supposed to be billed since it turns out the problem was on there end.)
0
 

Expert Comment

by:lltompkins
ID: 21870092
Glad to hear you got it up and running.  I kinda figured there was a problem on their end.
0
 
LVL 1

Accepted Solution

by:
Computer101 earned 0 total points
ID: 22445264
PAQed with points refunded (500)

Computer101
EE Admin
0

Featured Post

Connect further...control easier

With the ATEN CE624, you can now enjoy a high-quality visual experience powered by HDBaseT technology and the convenience of a single Cat6 cable to transmit uncompressed video with zero latency and multi-streaming for dual-view applications where remote access is required.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

When you try to share a printer , you may receive one of the following error messages. Error message when you use the Add Printer Wizard to share a printer: Windows could not share your printer. Operation could not be completed (Error 0x000006…
This article is a collection of issues that people face from time to time and possible solutions to those issues. I hope you enjoy reading it.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Michael from AdRem Software explains how to view the most utilized and worst performing nodes in your network, by accessing the Top Charts view in NetCrunch network monitor (https://www.adremsoft.com/). Top Charts is a view in which you can set seve…

705 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question