Solved

Dual Concurrent T1 Cisco Router Configuration Template

Posted on 2008-06-24
3
339 Views
Last Modified: 2012-05-05
I have a client that has a Cisco 1841 Router with a single T1 connected to it.  It runs everything from NAT's to VPNs.  

They are getting a second T1 to do a special type of configuration that I know for a fact can be done (just not sure how).

They want the new T1 to only be used for http,https and ftp outbound traffic.  All other traffic, NATS and VPNS will still be on the old T1.

They also have a 2nd WIC and Ethernet port installed.

What I need is just a template or ideas on what type of configuration would be needed.  I am doing this Thursday June 26th so any help would be awesome!!!!!!

Please let me know if any further information is needed.
0
Comment
Question by:ericmmonda
  • 2
3 Comments
 
LVL 7

Accepted Solution

by:
logic2 earned 500 total points
ID: 21862518
Policy based routing should be the answer
try doing something like the below i guess this should do the trick just hope it doesnt block other traffic :) so test it in off business hours :)

Router(config)#int fa0/0   <<< your LAN interface
Router(config-if)#ip policy route-map MATCH_INTERNET

Router(config-if)#route-map MATCH_INTERNET
Router(config-route-map)#match ip address MATCH_INTERNET
Router(config-route-map)#set ip next-hop 50.50.50.50    <<< The remote end of the new T1

Router(config)#ip access-list extended MATCH_INTERNET
Router(config-ext-nacl)#permit tcp any any eq 80
Router(config-ext-nacl)#permit tcp any any eq 8080
Router(config-ext-nacl)#permit tcp any any eq 443
Router(config-ext-nacl)#permit tcp any any eq 21
Router(config-ext-nacl)#permit tcp any any eq 20
0
 

Author Comment

by:ericmmonda
ID: 21865989
Logic2,
Thanks for the quick reply.

That seems to be very logical.  I have never used a policy based config.  

Just to make sure I understand it correctly....
Router(config-route-map)#set ip next-hop 50.50.50.50    <<< The remote end of the new T1
Are you talking about the T1 gateway?

Thanks
0
 
LVL 7

Expert Comment

by:logic2
ID: 21880485
mmm not sure but let me explain

my router with ip x.x.x.x -------------- T1 -------------- Service Provider with ip y.y.y.y
so in our case the next hop would be the y.y.y.y
0

Featured Post

Is Your Active Directory as Secure as You Think?

More than 75% of all records are compromised because of the loss or theft of a privileged credential. Experts have been exploring Active Directory infrastructure to identify key threats and establish best practices for keeping data safe. Attend this month’s webinar to learn more.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

While it is possible to put two routes in place with the secondary having a higher metric, this may not always work. In the event of a failure that does not bring down the physical interface on the router the primary route is not removed. There is a…
This article is a guide to configure bridging on Cisco Routers.  This is something I never knew was possible until after making a few phone calls to Cisco.  Using bridging saved our company money by not requiring us to purchase a new switch.  Bridgi…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

914 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

20 Experts available now in Live!

Get 1:1 Help Now