asked on
Configuring PIX 501 and getting GUI to work
(New info - got GUI working again - didn't save config and rebooted - )
OK.. This is my issue. I have a PIX 501 that ws given to me to configure. I thought I was relatively solid technically.. well I give. I have pix so you can get in with the console and you could at one point get into the GUI.. I simply wanted to accomplish the following. This was going to have a web server internally with a Public fixed IP. I wanted to open up a few ports - i.e Port 80, 443 etc. Needles to say I had no luck. With all my attempts to get it to work I also broke the connection to the GUI. Here is my config .
PIX Version 6.3(5)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname pixfirewall
domain-name ciscopix.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
name 192.168.1.233 ALSI
access-list outside_access_in permit tcp any host ALSI
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside 200.200.200.77 255.255.255.0
ip address inside 192.168.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm location ALSI 255.255.255.255 inside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) ALSI ALSI netmask 255.255.255.255 0 0
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 200.200.200.1 1
route inside ALSI 255.255.255.255 200.200.200.77 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.1.2-192.168.1.33 inside
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
terminal width 80
Cryptochecksum:51a41147ffd
Please help me by firstly getting the GUI back working (Fixed). This will only have the server on this network but I may have a workstation for admin. I also want the server to be able to go out to get updates. The net config will be as follows - modem / firewall / server . Plain and simple. I have not found any decent documentation for the GUI so for right now if someone can just give me the commands for console that will work. (So I just want traffic to got out from the lan side and only open ports I want to come in from the outside. - sounds simple)
Thanks in advance
OK.. This is my issue. I have a PIX 501 that ws given to me to configure. I thought I was relatively solid technically.. well I give. I have pix so you can get in with the console and you could at one point get into the GUI.. I simply wanted to accomplish the following. This was going to have a web server internally with a Public fixed IP. I wanted to open up a few ports - i.e Port 80, 443 etc. Needles to say I had no luck. With all my attempts to get it to work I also broke the connection to the GUI. Here is my config .
PIX Version 6.3(5)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname pixfirewall
domain-name ciscopix.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
name 192.168.1.233 ALSI
access-list outside_access_in permit tcp any host ALSI
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside 200.200.200.77 255.255.255.0
ip address inside 192.168.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm location ALSI 255.255.255.255 inside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) ALSI ALSI netmask 255.255.255.255 0 0
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 200.200.200.1 1
route inside ALSI 255.255.255.255 200.200.200.77 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.1.2-192.168.1.33 inside
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
terminal width 80
Cryptochecksum:51a41147ffd
Please help me by firstly getting the GUI back working (Fixed). This will only have the server on this network but I may have a workstation for admin. I also want the server to be able to go out to get updates. The net config will be as follows - modem / firewall / server . Plain and simple. I have not found any decent documentation for the GUI so for right now if someone can just give me the commands for console that will work. (So I just want traffic to got out from the lan side and only open ports I want to come in from the outside. - sounds simple)
Thanks in advance
Cisco
Last Comment
Vee_Mod