Solved

BGP Re-configuring same same neighbor with some other peer-group

Posted on 2008-09-30
3
913 Views
Last Modified: 2008-10-06
Hi,

I am trying re-configure the peer-group for particular neighbor after removing the old peer-group from the same neighbor but I am getting the following message while applying the new config.

old config:

router bgp 6
address-family ipv4 vrf test
neighbor logo1 peer-group
neighbor logo1 remote-as 7
neighbor logo1 activate
neighbor logo1 update-source vlan100
neighbor logo2 peer-group
neighbor logo2 remote-as 7
neighbor logo2 activate
neighbor logo2 update-source vlan101

I am just doing the below commands on the config mode:

no neighbor 1.1.1.1 peer-group logo1
neighbor 1.1.1.1 peer-group logo2
% Cannot change the peer-group. Deconfigure first

Getting the above message...

Thanks,
Mohamed



0
Comment
Question by:Mohamedsadath
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
3 Comments
 
LVL 7

Expert Comment

by:dkarpekin
ID: 22607033
active-cac-policy-set
To set the active CAC policy set within a signaling border element (SBE) entity, use the active-cac-policy-set command in SBE configuration mode. To deconfigure the active policy set, leaving the SBE with no active policy set, use the no form of this command.

active-cac-policy-set {policy-set-id}

no active-cac-policy-set {policy-set-id}

0
 
LVL 79

Expert Comment

by:lrmoore
ID: 22611148
@ dkarpekin  ??? huh???

Remove the logo1 commands first

router bgp 6
no neighbor logo1 peer-group
no neighbor logo1 remote-as 7
no neighbor logo1 activate
no neighbor logo1 update-source vlan100
neighbor 1.1.1.1 peer-group logo2
0
 

Accepted Solution

by:
Mohamedsadath earned 0 total points
ID: 22615278
No, I can't remove logo1 peer-group as it is used by other neighbors on the same address-family. this problem is caused by a software problem, where the neighbor even when removed from the peer group in the configuration, it remains member of the peer group in memory.

cannot change peer-group msg while configuring peer-group


Router(config-router-af)#neighbor peer-group % Cannot change the peer-group. Deconfigure first

A possible workaround is to remove the neighbor configuration with the "no neighbor" command, removing the neighbor totally from the configuration and adding it again with the new peer group.
Another workaround is to reload the equipment and add it to the new peer group after it has reloaded.
0

Featured Post

Independent Software Vendors: We Want Your Opinion

We value your feedback.

Take our survey and automatically be enter to win anyone of the following:
Yeti Cooler, Amazon eGift Card, and Movie eGift Card!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Communicating machines through cross-over cable? 5 95
unable to set full duplex 100 on WAN interface 11 99
Extended ping 6 55
Advice on router and switch 25 83
Problem Description:   Couple of months ago we upgraded the ADSL line at our branch office from Home to Business line. The purpose of transforming the service to have static public IP’s. We were in need for public IP’s to publish our web resour…
In the world of WAN, QoS is a pretty important topic for most, if not all, networks. Some WAN technologies have QoS mechanisms built in, but others, such as some L2 WAN's, don't have QoS control in the provider cloud.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

732 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question