Solved

CISCO 1603 R router

Posted on 2008-10-07
4
262 Views
Last Modified: 2012-05-05
I have a cisco 1603 R Router , i am trying to give an ip address for sub interface and i am getting below error.  Flash & version details of router mentioned below.
******************************************************
Router#confi term
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#inter
Router(config)#interface ether
Router(config)#interface ethernet 0.1
Router(config-subif)#ip address 192.168.0.1 255.255.255.0

Configuring IP routing on a LAN subinterface is only allowed if that
subinterface is already configured as part of an IEEE 802.10 or ISL vLAN.

Router(config-subif)#

************************************************************************************************
Flash
=====
PCMCIA flash directory:
File  Length   Name/status
  1   2226518  c1600-y-mz.120-12
[2226584 bytes used, 1967720 available, 4194304 total]
4096K bytes of processor board PCMCIA flash (Read/Write)


Vesrion
========
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-M), Version 12.0(12), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Mon 10-Jul-00 19:59 by htseng
Image text-base: 0x02005000, data-base: 0x0245E484

ROM: System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
ROM: 1600 Software (C1600-RBOOT-R), Version 12.0(3)T,  RELEASE SOFTWARE (fc1)

Router uptime is 53 minutes
System restarted by reload
System image file is "flash:c1600-y-mz.120-12"

cisco 1603 (68360) processor (revision C) with 6144K/2048K bytes of memory.
Processor board ID 26403016, with hardware revision 00000004
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
1 Ethernet/IEEE 802.3 interface(s)
1 ISDN Basic Rate interface(s)
System/IO memory with parity disabled
8192K bytes of DRAM onboard
System running from RAM
7K bytes of non-volatile configuration memory.
4096K bytes of processor board PCMCIA flash (Read/Write)

Configuration register is 0x2102
0
Comment
Question by:WILSON123J
  • 2
  • 2
4 Comments
 
LVL 43

Expert Comment

by:JFrederick29
ID: 22658481
You need an IP PLUS image (you have an IP image) and unfortunately you would need to upgrade the DRAM and Flash depending on which image you were going to go with.  Looking at Cisco's site, you can't get an IP PLUS image that will work with your routers memory.
0
 

Author Comment

by:WILSON123J
ID: 22666189
Please let me know from where i can get this . CISCO site is asking for username and password.
If possible please send to wils_john@hotmail.com
0
 
LVL 43

Accepted Solution

by:
JFrederick29 earned 500 total points
ID: 22668321
Well, as I said, the problem is that you can no longer get an image from Cisco that fits on your router.  You need to upgrade the RAM and Flash on the router to support a newer image that has the feature you need.
0
 

Author Closing Comment

by:WILSON123J
ID: 31503744
Thanks a  lot , i will go fo a new router.
0

Featured Post

PRTG Network Monitor: Intuitive Network Monitoring

Network Monitoring is essential to ensure that computer systems and network devices are running. Use PRTG to monitor LANs, servers, websites, applications and devices, bandwidth, virtual environments, remote systems, IoT, and many more. PRTG is easy to set up & use.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Access shared drive during VPN session 9 108
How to configure AT&T Netgate with Sonicwall Firewall 24 67
Configuring EIGRP with neighbor command 25 60
Failover VDSL Modems 3 71
In this tutorial I will show you with short command examples how to obtain a packet footprint of all traffic flowing thru your Juniper device running ScreenOS. I do not know the exact firmware requirement, but I think the fprofile command is availab…
Quality of Service (QoS) options are nearly endless when it comes to networks today. This article is merely one example of how it can be handled in a hub-n-spoke design using a 3-tier configuration.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

810 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question