Solved

What do I do with this error code?

Posted on 2008-10-09
3
3,991 Views
Last Modified: 2012-09-05
The Exact Error is:

The error code was 3221684226. The message was The system cannot find the file specified..

During Re-Install, The server was erased and reinstalled during pre-production. I believe I have removed the product info properly from my AD server, now the install gives this error during the GUI organization prep.

Any ideas what I may have missed? Note the F: Drive does not exist on this computer.

Server 2008 x64 Exchange 2007 sp1 Microsoft Media.

Log Snippett:

[10/9/2008 3:03:33 PM] [2] Entering ScInstallLDIFScript
[10/9/2008 3:03:33 PM] [2]  ScRunLDIFScript (f:\08.01.0240\sources\dev\admin\src\libs\exsetup\exmisc.cxx:888)
           Error code 0XC0070002 (2): The system cannot find the file specified.
[10/9/2008 3:03:33 PM] [2]  ScInstallLDIFScript (f:\08.01.0240\sources\dev\admin\src\libs\exsetup\server.cxx:149)
           Error code 0XC0070002 (2): The system cannot find the file specified.
[10/9/2008 3:03:33 PM] [2] Leaving ScInstallLDIFScript
[10/9/2008 3:03:33 PM] [2]  CAtomOrgLevelCt::ScAddDSObjects (f:\08.01.0240\sources\dev\admin\src\udog\exsetdata\components\server\a_orglevelct.cxx:379)
           Error code 0XC0070002 (2): The system cannot find the file specified.
[10/9/2008 3:03:33 PM] [2] Leaving CAtomOrgLevelCt::ScAddDSObjects
[10/9/2008 3:03:33 PM] [2]  CAtomOrgLevelCt::ScAdd (f:\08.01.0240\sources\dev\admin\src\udog\exsetdata\components\server\a_orglevelct.cxx:138)
           Error code 0XC0070002 (2): The system cannot find the file specified.
[10/9/2008 3:03:33 PM] [2] Leaving CAtomOrgLevelCt::ScAdd
[10/9/2008 3:03:33 PM] [2] mode = 'Install' (61953) CBaseAtom::ScSetup (f:\08.01.0240\sources\dev\admin\src\udog\setupbase\basecomp\baseatom.cxx:535)
           Error code 0XC0070002 (2): The system cannot find the file specified.
[10/9/2008 3:03:33 PM] [2]  ScSetupAtom (f:\08.01.0240\sources\dev\admin\src\udog\exsetdata\exsetds.cxx:897)
           Error code 0XC0070002 (2): The system cannot find the file specified.
[10/9/2008 3:03:33 PM] [2] Leaving ScSetupAtom
[10/9/2008 3:03:33 PM] [2] [ERROR] An error occurred. The error code was 3221684226. The message was The system cannot find the file specified..
[10/9/2008 3:03:33 PM] [1] The following 1 error(s) occurred during task execution:
[10/9/2008 3:03:33 PM] [1] 0.  ErrorRecord: An error occurred. The error code was 3221684226. The message was The system cannot find the file specified..
[10/9/2008 3:03:33 PM] [1] 0.  ErrorRecord: Microsoft.Exchange.Management.Deployment.ExsetdataException: An error occurred. The error code was 3221684226. The message was The system cannot find the file specified..
[10/9/2008 3:03:33 PM] [1] [ERROR] An error occurred. The error code was 3221684226. The message was The system cannot find the file specified..
[10/9/2008 3:03:33 PM] [1] Setup is halting task execution because of one or more errors in a critical task.
[10/9/2008 3:03:33 PM] [1] Finished executing component tasks.
[10/9/2008 3:03:33 PM] [1] Ending processing.
0
Comment
Question by:i8yurdog
3 Comments
 
LVL 9

Accepted Solution

by:
abdulzis earned 500 total points
ID: 22684475
Have you installed RSAT-ADDS?

You will need to run the following command and reboot the server.

ServerManagerCmd -i RSAT-ADDS

refer: http://technet.microsoft.com/en-us/library/bb691354(EXCHG.80).aspx
0
 

Author Closing Comment

by:i8yurdog
ID: 31504863
Great, and doggone it if I didn't see that and simply over look it. You're my hero!
0

Featured Post

Best Practices: Disaster Recovery Testing

Besides backup, any IT division should have a disaster recovery plan. You will find a few tips below relating to the development of such a plan and to what issues one should pay special attention in the course of backup planning.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Utilizing an array to gracefully append to a list of EmailAddresses
Learn to move / copy / export exchange contacts to iPhone without using any software. Also see the issues in configuration of exchange with iPhone to migrate contacts.
To show how to create a transport rule in Exchange 2013. We show this process by using the Exchange Admin Center. Log into Exchange Admin Center.: First we need to log into the Exchange Admin Center. Navigate to the Mail Flow >> Rules tab.:  To cr…
The video tutorial explains the basics of the Exchange server Database Availability groups. The components of this video include: 1. Automatic Failover 2. Failover Clustering 3. Active Manager

929 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

11 Experts available now in Live!

Get 1:1 Help Now