Want to win a PS4? Go Premium and enter to win our High-Tech Treats giveaway. Enter to Win

x
?
Solved

How can i view the NAT (?) on my IBM 2210 router?

Posted on 2008-10-14
10
Medium Priority
?
472 Views
Last Modified: 2010-04-21
I need help in viewing my router config.  I'm trying to see all the IP info that are loaded for the rest of my routers on my WAN.
I'm looking for the actual telnet command to view it.  My windows config sw does not work.
THANKS!
ST
0
Comment
Question by:ststst
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 5
  • 5
10 Comments
 
LVL 22

Expert Comment

by:Rick Hobbs
ID: 22714170
I believe it is "show ip nat translation"
0
 

Author Comment

by:ststst
ID: 22714233
Hi Rick
I'm looking for the actual command after i enter the T5 or T6.
ST
0
 
LVL 22

Expert Comment

by:Rick Hobbs
ID: 22714833
Here is the complete command reference guide.  
http://www.redbooks.ibm.com/abstracts/sg244446.html
0
What does it mean to be "Always On"?

Is your cloud always on? With an Always On cloud you won't have to worry about downtime for maintenance or software application code updates, ensuring that your bottom line isn't affected.

 

Author Comment

by:ststst
ID: 22715660
There are too many pages to search thru.  I wanted a quicker result
0
 

Author Comment

by:ststst
ID: 22715914
I can list the static routes.  i cannot get into the NAT.  Is static routes the same as NAT?  
0
 
LVL 22

Expert Comment

by:Rick Hobbs
ID: 22718375
Basically, yes.  The internal private address to the external public address is the NAT translation.  If the router also does PAT, that occurs on the NATted translations.
0
 
LVL 22

Accepted Solution

by:
Rick Hobbs earned 500 total points
ID: 22718402
OK. I read the manual for you.  The router only does NAT one-to-one translation so your route table is it.
0
 

Author Comment

by:ststst
ID: 22722750
Thanks Rick.  I've looked too and looks like my NAT was not on.  I'll double check the route table - i did see that.
ST
0
 

Author Closing Comment

by:ststst
ID: 31506016
the manual was a big book... i'm only 1/3 the way down but found what i needed.
0
 
LVL 22

Expert Comment

by:Rick Hobbs
ID: 22725365
Glad I was able to be of some assistance.
0

Featured Post

How to Use the Help Bell

Need to boost the visibility of your question for solutions? Use the Experts Exchange Help Bell to confirm priority levels and contact subject-matter experts for question attention.  Check out this how-to article for more information.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

In this tutorial I will show you with short command examples how to obtain a packet footprint of all traffic flowing thru your Juniper device running ScreenOS. I do not know the exact firmware requirement, but I think the fprofile command is availab…
I have seen some questions on problems with SSH/telnet access to Cisco routers that may occur despite the fact that from a PC connected to your LAN, Internet connectivity is in place and users can access Internet sites without any issues.  There are…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses

636 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question