Solved

bigip ltm new setup, node routing problem?

Posted on 2008-10-14
1
1,238 Views
Last Modified: 2012-05-05
I'm setting up a new bigip box. I setup the interface, pools, virtual servers, etc. for a web site. When I tested it out the following statistics are shown.
                     |  bits  since       |  bits  in prior    |  current
                     |  Oct 14 11:00:14   |  5 seconds         |  time
BIG-IP      ACTIVE   |---In----Out---Conn-|---In----Out---Conn-|  12:52:48
bigip1.acompany.com 122032  43520     33      0      0      0

VIRTUAL ip:port      |---In----Out---Conn-|---In----Out---Conn-|-Nodes Up--
192.168.59.64:http    121600  43520     32      0      0      0      2
192.168.59.64:https        0      0      0      0      0      0      2

NODE ip:port         |---In----Out---Conn-|---In----Out---Conn-|--State----
192.168.55.46:http     30912      0     12      0      0      0 UNCHECKED
192.168.55.47:http     30912      0     12      0      0      0 UNCHECKED
192.168.55.43:38080    10304      0      4      0      0      0 UNCHECKED
192.168.55.44:38080    10304      0      4      0      0      0 UNCHECKED
192.168.55.43:38082        0      0      0      0      0      0 UNCHECKED
192.168.55.44:38082        0      0      0      0      0      0 UNCHECKED
192.168.55.43:38083        0      0      0      0      0      0 UNCHECKED
192.168.55.46:https        0      0      0      0      0      0 UNCHECKED
192.168.55.47:https        0      0      0      0      0      0 UNCHECKED

This is what netstat -rn shows
Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface
127.1.1.0       0.0.0.0         255.255.255.248 U         0 0          0 tmm0
192.168.55.32   0.0.0.0         255.255.255.224 U         0 0          0 internal
10.40.9.0       0.0.0.0         255.255.255.0   U         0 0          0 eth0
127.2.0.0       0.0.0.0         255.255.255.0   U         0 0          0 eth0
192.168.59.0    0.0.0.0         255.255.255.0   U         0 0          0 external
127.0.0.0       -               255.0.0.0       !         - -          - -
0.0.0.0         10.40.9.27      0.0.0.0         UG        0 0          0 eth0

So here are my questions.
1. What is my problem? Lets keep it specific to the problem described above. :)
2. Does the netstat -rn command need a gateway defined or is it sufficient to just have the interface defined?

Thanks in advanced.
0
Comment
Question by:jsfald
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
1 Comment
 
LVL 1

Accepted Solution

by:
jsfald earned 0 total points
ID: 22727336
The problem was with the node/server. It didn't have a proper default route. Making the default route point to the floating ip of the f5 fixed the problem. I'll ask community support to close the question.
0

Featured Post

Manage your data center from practically anywhere

The KN8164V features HD resolution of 1920 x 1200, FIPS 140-2 with level 1 security standards and virtual media transmissions at twice the speed. Built for reliability, the KN series provides local console and remote over IP access, ensuring 24/7 availability to all servers.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Multiple Static IP addresses on Router 14 204
Create remote access home server 4 116
How VPC help preventing STP Loops 4 151
Configure 2 Servers with Crossover cable 3 22
If you’re like me and you like peace and quiet, saving money, and pretty lights, then this article is for you. For financial reasons, I buy all the Cisco equipment for my home lab second-hand. The first thing to wear out is usually one of the coo…
Do you have a computer or other electronic gear that is attached to a rat nest of cables, or alternatively have your cables all bundled nice at neat?  If so then read this post to sidstep common pitfalls. When I was a student at DeVry University,…
In an interesting question (https://www.experts-exchange.com/questions/29008360/) here at Experts Exchange, a member asked how to split a single image into multiple images. The primary usage for this is to place many photographs on a flatbed scanner…

730 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question