[2 days left] What’s wrong with your cloud strategy? Learn why multicloud solutions matter with Nimble Storage.Register Now

x
?
Solved

bridge network and ip assigned

Posted on 2008-10-15
5
Medium Priority
?
247 Views
Last Modified: 2013-11-09
scenario:
1 notebook with wireless card connected to dlink router wireless
1 pc pdc connected to notebook by switch using ethernet lan in another room.
i' don't want to buy another wireless card for pdc so can i using bridging between lan and wireless connection but the ip of notebook become 165.xx.xx.xx
so notebook doesn't see domain pdc (10.xxx.xxx.xxx class).
so must i change the address of notebook and domain to make lan works?
can i use internet connection sharing? why in this case xp says " address will change to 192.xx.xxx..xxx
this mean also in this case i cannot use my originale 10.xx.xx.xx class?
ABSURD!
0
Comment
Question by:tsubasa74j
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 3
  • 2
5 Comments
 
LVL 57

Expert Comment

by:giltjr
ID: 22727705
Bridging is done at layer 2 (Ethernet).  Routing is done at layer 3  IP.

Why do you have two IP subnets?  What I would suggest is that you either configure your wireless router to assign DHCP addresses in the 10.x.x.x subnet you have, or just reconfigure it to use 10.x.x.x instead of 192.168.1.0/24.

If you want to keep both subnets, then you need to setup something as a router and get it with IP addresses on both IP subnets.

0
 

Author Comment

by:tsubasa74j
ID: 22730317
i've three items notebook on class 10.xxx - pdc on class. 10.xxxx - router on class 10.xxxx
as you knoe security level consider more affidable class of this type that not a class c.
i don't want to explain why, i only want to use my notebook wireless connection to share it with my pc in ethernet lan.
is there a simple mode to do it? or must i change class ip anywhere?
thanks
0
 
LVL 57

Expert Comment

by:giltjr
ID: 22730485
Security has nothing to do with what class you have.  In fact class is really out the door.  The security deals with using non-public IP addresses.  Both the 10.0.0.0/8 and 192.168.0.0/16 ranges are non-public IP address and would be considered secure, as neither of them can be routed over the public Internet.

If both the 10.x.x.x and 192.168.x.x subnets are within your home and your network, then I would suggest that you change one of them so that you have a single IP subnet.  If you don't then you need either to have something act as a router that can route between the two IP subnets, or you need to be able to have either the server or you laptop have two IP addresses, one in each subnet.

Think of it this way, say you only speak Spanish (10.x.x.x subnet) and I only talk French (192.168.x.x).  Either one of us must learn to speak the other language or we need to get a translator (router).  There is no magic that would allow each of us to continue to speak our own languages and understand each other.
0
 

Author Comment

by:tsubasa74j
ID: 23037076
ok thnak for explanation so i have 2 identical network segments 10.0.xxxx.xxxx and now?
 - my notebook is wireles connected to the router
 - my pc is ethernet-lan connected to the notebook
 - i've no money to buy wireless card for my pc (windows 2000 server)
router isfar from my pc and notebook room, how can i use notebook wireless-dsl connection or is there  a mode to give dsl to my pc in lan?
thanks for all
Domenico
0
 
LVL 57

Accepted Solution

by:
giltjr earned 1500 total points
ID: 23053482
What are you calling "segments?"  If you have a Wireless Access point with wired switch ports also, these will be treated as a single segment, and they should both be on the same IP subnet.  The the wireless device you have is called a wireless router, then you might be getting a bit confused.

On a wireless router there are typically 4 wired ports that are part of the wireless network and then a 5 ports that is labeled WAN.  The WAN port is not part of the wireless and the 4 wired ports segment.  The wireless router will route between the WAN port and all of the other ports and the wireless network.  The WAN port is a unique segment and should be its own IP subnet.
0

Featured Post

Q2 2017 - Latest Malware & Internet Attacks

WatchGuard’s Threat Lab is a group of dedicated threat researchers committed to helping you stay ahead of the bad guys by providing in-depth analysis of the top security threats to your network.  Check out our latest Quarterly Internet Security Report!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

This article will inform Clients about common and important expectations from the freelancers (Experts) who are looking at your Gig.
This article explains the fundamentals of industrial networking which ultimately is the backbone network which is providing communications for process devices like robots and other not so interesting stuff.
Internet Business Fax to Email Made Easy - With  eFax Corporate (http://www.enterprise.efax.com), you'll receive a dedicated online fax number, which is used the same way as a typical analog fax number. You'll receive secure faxes in your email, f…
Monitoring a network: why having a policy is the best policy? Michael Kulchisky, MCSE, MCSA, MCP, VTSP, VSP, CCSP outlines the enormous benefits of having a policy-based approach when monitoring medium and large networks. Software utilized in this v…

656 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question