?
Solved

Insufficient resources to complete requested service

Posted on 2008-11-03
6
Medium Priority
?
370 Views
Last Modified: 2008-11-12
When copying files to this new system the network inevitably fails whether using one of two Vista Ultimate PCs or  Mac G5 OSX
Message is usually insufficient resources to complete requested service. LED them turns red. NAS has to be turned off and on again. Fails on either of the Raid 1 disk volumes
0
Comment
Question by:whamton
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 3
  • 3
6 Comments
 
LVL 7

Expert Comment

by:dkarpekin
ID: 22867561
Network/file sharing has to be enabled on Vista.
Also not really clearhow you attched to the NAS? by soft come with it?- if so than it have to be "Vista ready".
Or by "maping drives" ? - than WINS might need to be present, or else?
0
 

Author Comment

by:whamton
ID: 22874494
Thanks

NAS is attached to Netgear 10/100/1000 switch. All attached devices are 1G capable.
Acer Easystore has web based interface proprietary software - very basic to create users, shares etc.
Mapping is done on any PC/Mac. Drives are always accessible after rebooting the NAS but become unavailable part way through data transfer. Once file at a time is OK but bulk data transfer of any size causes the mapped drives to become unavailable. As you say is is probably a Vista problem but it does also happen with OS X 10.4. Transfer speed for the short while the transfer takes place is usually only 1.01mb

Whamton
0
 
LVL 7

Expert Comment

by:dkarpekin
ID: 22875991
You probably need config WINS, on any windows servers , and IP of it for every NIC, on network- properties-IP4- advance- put IP for WINS, and check mark "enable NetBios over ".
make sure there is no firewall blockage for NetBIos.
Beside that, permission needs to be set , to alow sharing, but this is prrobably done already.
Test actual speed PC-to-PC, across diffrent portion/diffrent OS and so on
Iperf 2.0.2 installer for Windows from    http://dast.nlanr.net/Projects/Iperf/   Look for kperf_setup.exe

This will help narrow down problem, find "bottleneck",cable problem, diffrents in file transfer type, and so on.
0
Flexible connectivity for any environment

The KE6900 series can extend and deploy computers with high definition displays across multiple stations in a variety of applications that suit any environment. Expand computer use to stations across multiple rooms with dynamic access.

 

Accepted Solution

by:
whamton earned 0 total points
ID: 22902973
Finally I have an answer. I have been monitoring the hard disks and finally today one disk of a raid volume is marked as having failed. It is very annoying for all concerned that it should be a hardware failure despite the fact that the infrequent (now constant) red led was supposed to be an indication of software failure. Now I need to return or have the disk replaced - personally I would like to never see it again
Whamton
0
 

Author Comment

by:whamton
ID: 22902981
Thank you for your ideas
Whamton
0
 
LVL 7

Expert Comment

by:dkarpekin
ID: 22904654
Ussially "thanks" for solutions expressed by points been assign.
0

Featured Post

Simplifying Server Workload Migrations

This use case outlines the migration challenges that organizations face and how the Acronis AnyData Engine supports physical-to-physical (P2P), physical-to-virtual (P2V), virtual to physical (V2P), and cross-virtual (V2V) migration scenarios to address these challenges.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Hi All Just a quick one for everybody. I was recently looking into setting the default User Account Picture for all my vista clients within the network but on closer inspection the group policy setting only allows you to set the default pictur…
So who is this article for? If you are like most of the computer users out there, you probably only realize the meaning of 'System maintenance' after something goes wrong. This article is for you if you care about keeping your system working opti…
The Task Scheduler is a powerful tool that is built into Windows. It allows you to schedule tasks (actions) on a recurring basis, such as hourly, daily, weekly, monthly, at log on, at startup, on idle, etc. This video Micro Tutorial is a brief intro…
Michael from AdRem Software explains how to view the most utilized and worst performing nodes in your network, by accessing the Top Charts view in NetCrunch network monitor (https://www.adremsoft.com/). Top Charts is a view in which you can set seve…
Suggested Courses
Course of the Month11 days, 13 hours left to enroll

752 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question